Topography data

The GeoClaw software for flow over topography requires at least one topo file to be input, see Specifying GeoClaw parameters in

Currently topo files are restricted to three possible formats as ASCII files. A future project is to allow other formats including NetCDF.

In the descriptions below it is assumed that the topo file gives the elevation of the topography (relative to some reference level) as a value of z at each (x,y) point on a rectangular grid. Only uniformly spaced rectangular topo grids are currently recognized.

More than one topo file can be specified (see Topography data file parameters) that might cover overlapping regions at different resolutions. The union of all the topo files should cover the full computational domain specified (and may extend outside it). Internally in GeoClaw a single piecewise-bilinear function is constructed from the union of the topo files, using the best information available in regions of overlap. This function is then integrated over computational grid cells to obtain the single topo value in each grid cell needed when solving depth averaged equations such as the shallow water equations with these finite volume methods. Note that this has the feature that if a grid cell is refined at some stage in the computation, the topo used in the fine cells have an average value that is equal to the coarse cell value. This is crucial in maintaining the ocean-at-rest steady state, for example.

The recognized topotypes are:

topotype = 1

x,y,z values on each line, progressing from upper left (NW) corner across rows (moving east), then down in standard GIS form. The size of the grid and spacing between the grid points is deduced from the data.

Example: if you want a flat bottom at B = -1000. over a domain 0. <= x <= 10. and 20. <= y <= 30. then the topo file could be simply:

0.  30.  -1000.
10. 30.  -1000.
0.  20.  -1000.
10. 20.  -1000.

These files are larger than necessary since they store the x,y values at each point even though the points are required to be equally spaced. Many data sets come this way, but note that you can convert a file of this type to one of the more compact types below using pyclaw.geotools.topotools.converttopotype(inputfile, outputfile, topotypein=1, topotypeout=2, nodata_value=None).

topotype = 2

The file starts with a header consisting of 6 lines containing:


and is followed by mx*my lines containing the z values at each x,y, again progressing from upper left (NW) corner across rows (moving east), then down in standard GIS form. The lower left corner of the grid is (xllcorner, yllcorner) and the distance between grid points in both x and y is cellsize. The value nodataval indicates what value of z is specified for missing data points (often something like 9999. in data sets with missing values).

Example: For the same example as above, the topo file with topotype==2 would be:

2         mx
2         my
0.        xllcorner
20.       yllcorner
10.       cellsize
9999.     nodatavalue

topotype = 3

The file starts with a header consisting of 6 lines as for topotype=2, followed by my lines, each containing mx values for one row of data (ordered as before, so the first line of data is the northernmost line of data, going from west to east).

Example: For the same example as above, the topo file with topotype==3 would be:

2         mx
2         my
0.        xllcorner
20.       yllcorner
10.       cellsize
9999.     nodatavalue
-1000.  -1000.
-1000.  -1000.

It is also possible to specify values -1, -2, or -3 for topotype, in which case the z values will be negated as they are read in (since some data sets use different convensions for positive and negative values relative to sea level).

For GeoClaw applications in the ocean or lakes (such as tsunami modeling), it is generally assumed that sealevel = 0 has been set in Tsunami parameters and that z<0 corresponds to subsurface bathymetry and z>0 to topograpy above sea level.

Downloading topography files

The example $CLAW/apps/tsunami/chile2010 is set up to automatically download topo files via:

$ make topo

See the file in that directory.

Other such examples will appear in the future.

Several on-line databases are available for topograpy, e.g.

Topography displacement files

For tsunami generation a file dtopo is generally used to specify the displacement of the topography relative to that specified in the topo files.

Currently two formats are supported for this file:


Similar to topo files with topotype=1 as described above, except that each line starts with a t value for the time, so each line contains t,x,y,dz

The x,y,dz values give the displacement dz at x,y at time t. It is assumed that the grid is uniform and that the file contains mx*my*mt lines if mt different times are specified for an mx*my grid.


Similar to topo files with topotype=3 as described above, but the header is different, and contains lines specifying mx, my, mt, xlower, ylower, t0, dx, dy, and dt. These are followed by mt sets of my lines, each line containing mx values of dz.

The Okada model can be used to generate dtopo files from fault parameters, as described in Earthquake sources: Fault slip and the Okada model.

qinit data file

Instead of (or in addition to) specifying a displacement of the topography it is possible to specify a perturbation to the depth, momentum, or surface elevation of the initial data. This is generally useful only for tsunami modeling where the initial data specified in the default qinit_geo.f function is the stationary water with surface elevation equal to sealevel as set in Tsunami parameters.

Of course it is possible to copy the qinit_geo.f function to your directory and modify it, but for some applications the initial elevation may be given on grid of the same type as described above. In this case file can be provided as described at qinit data file parameters containing this perturbation.

The file format is similar to what is described above for topotype=1, but now each line contains x,y,dq where dq is a perturbation to one of the components of q as specified by the value of iqinit specified (see qinit data file parameters). If iqinit = 4, the value dq is instead the surface elevation desired for the initial data and the depth h (first component of q) is set accordingly.

Table Of Contents

Previous topic

Cautionary Hints on using GeoClaw

Next topic

Specifying GeoClaw parameters in

This Page