Abstract:
Increasing traffic volumes and a deteriorating transportation infrastructure have stimulated the development of new systems and methods to accelerate the construction of highway bridges. Precast concrete bridge components offer a potential alternative to conventional reinforced, cast-in-place concrete components. The use of precast components has the potential to minimize traffic disruptions, improve work zone safety, reduce environmental impacts, improve constructability, increase quality, and lower life-cycle costs. This study compared two precast concrete bridge pier systems for rapid construction of bridges in seismic regions. One was a reinforced concrete system, in which mild steel deformed bars connect the precast concrete components and provide the flexural strength of the columns. The other was a hybrid system, which uses a combination of unbonded post-tensioning and mild steel deformed bars to make the connections. A parametric study of the two types of systems was conducted using nonlinear finite element models to investigate the global response and likelihood of damage for various frame configurations. On the basis of this study, a practical method was developed to estimate maximum seismic displacements from the cracked section properties of the columns, the elastic design displacement response spectrum, and the base-shear strength ratio. The results of the global nonlinear finite element analyses suggest that the systems have the potential for good seismic performance. Further analytical and experimental research is needed to investigate the constructability and seismic performance of the connection details.

Authors:
Hieber,D. G., Wacker,J. M., Eberhard,M. O., Stanton,J. F.

Keywords:
Alternative, bridge, bridges, columns, concrete, concrete bridge, connections, constructability, construction, cost, costs, damage, design, developed, development, environmental, environmental impact experimental, finite element, highway, impact, impacts, infrastructure, methods, models, performance piers, precast, precast concrete, prestressed concete, quality, Rapid construction, Regions, reinforce concrete, research, response spectra, response spectrum, safety, seismic, seismic performance, steel strength, Study, substructures, System, systems, traffic, traffic volumes, trasportation, volume

Download Report:

External Links: http://www.wsdot.wa.gov/research/reports/fullreports/611.1.pdf http://wsdot.wa.gov/Research/Reports/600/611.1.htm

Abstract:
This research addresses the understanding of, and need for, load spectra in future pavement design procedures and as a stepping stone toward more complete pavement design. The primary objective of this project was to develop truck axle load spectra for Washington State. To do this, axle load data collected at WIM stations throughout Washington State were used. The developed load spectra encompass the principal truck axles on the roadway network: single, tandem, and tridem. Achieving this objective allows the Washington State Department of Transportation, or any state highway agency with analogous traffic patterns, to accommodate the requirements of the 2002 Design Guide, developed through NCHRP Project 1-37A. A secondary objective of this project was to determine whether ESALs obtained from the developed load spectra are significantly different from historical values. Because the developed load spectra are transformable to ESALs, state highway agencies that decide not to use the new guide can still choose to employ the ESALs produced with the load spectra. The project concluded that the developed load spectra are reasonable. For single axles they are comparable to the 2002 Design Guide and MnROAD defaults. For tandem and tridem axles, they are slightly more conservative than defaults of the 2002 Design Guide and MnROAD, but they are still within reason. In addition, the ESALs per vehicle class associated with the developed load spectra are comparable to Washington State historical ESALs for vehicle classes 9, 10, and 13. The use of the newly developed ESALs per vehicle will generally increase design ESALs, but that increase will be due to inclusion of the less predominant vehicle classes (4, 6, 7, 8, and 11).

Authors:
Al-Yagout,M. A., Mahoney,J. P., Pierce,L., Hallenbeck,M. E.

Keywords:
agencies, axle, data, design, developed, development, equivalent single axel load, ESAL, highway, load spectra, pavement, pavement design, performance, project, research, roadway, single axle, traffic, transportation, truck, Washington, Washington state, weigh-in-motion, WIM

Download Report:

External Links: http://www.wsdot.wa.gov/research/reports/fullreports/600.1.pdf http://wsdot.wa.gov/Research/Reports/600/600.1.htm

Abstract:
This project performed extensive study and systematic research on the application of the Highway Development and Management system (HDM-4) to the Washington State Department of Transportation (WSDOT) highway system. Data processing, testing, calibration, and analysis were executed to provide the WSDOT with a new budget planning tool. HDM-4 flexible pavement deterioration models were calibrated with the assistance of the Washington State Pavement Management System. A method to calibrate concrete pavement distress models is proposed. This research also explored the application of HDM-4 analysis at the project, program, and strategic levels. The applications include prediction of pavement conditions during a defined analysis period, calculation of required budgets for optimal pavement conditions and maximum economic indicators, establishment of optimized work programs under varying levels of constrained budgets, and other applications for WSDOT.

Authors:
Li,J., Muench,S. T., Mahoney,J. P., Pierce,L., Sivaneswaran,N.

Keywords:
HDM-4, models, pavement maintenance, pavement management, pavement performance, Pavement preservation, vehicle operating costs, research, highway, development, management, management system, Washington, Washington state, transportation, WSDOT, data, calibration, analysis, planning, pavement, deterioration, concrete, program, applications, prediction, condition, indicators

Download Report:

External Links: http://www.wsdot.wa.gov/research/reports/fullreports/588.1.pdf http://wsdot.wa.gov/Research/Reports/500/588.1.htm

Abstract:
This research study was conducted to evaluate the in-service performance of existing guardrail end treatments and unrestrained pre-cast concrete barrier in Washington State. For a selected area of the state highway system over a one-year period, local area maintenance personnel were tasked to document incidents, including extent of damage and repair costs, into a database using NCHRP Project 22-13 methodology. Additional information (accident severity, e.g.) from police reports was gathered from the incidents and added to the database. The installation characteristics measured for Breakaway Cable Terminals (BCT) and Slotted Rail Terminals (SRT), along with the related crash data for these devices, showed overall acceptable performance when struck. Review of the incident severities, together with the displacement and damage data on struck barriers in the study area, revealed no significant difference in BCT and SRT performance. The installation, damage, and displacement characteristics examined on struck concrete barrier showed that the pin and loop connections were holding well in incidents, and the barrier displacements during incidents were within the WSDOT design specification for such systems.

Authors:
Igharo,P. O., Murphy,J., Glad,R. W.

Keywords:
performance, guardrail, Washington, Washington state, guardrail end treaments, breakaway cable terminal (BCT), roadside safety, slotted rail terminal (SRT), research, end treatment, precast concrete, concrete, concrete barrier, highway, maintenance, incident, damage, repair, costs, cost, database, methodology, accident severity, data, barriers, WSDOT, design, specification, systems

Download Report:

External Links: http://www.wsdot.wa.gov/research/reports/fullreports/580.1.pdf http://wsdot.wa.gov/Research/Reports/500/580.1.htm

Abstract:
This report identifies the key issues that must be considered by state and other highway operating agencies in selecting traffic equipment for collecting the truck volumes and load spectra needed for analysis and design of pavement structures. The report also identifies steps that must be taken to ensure that the equipment performs appropriately and that, as a consequence, the data collected accurately describe the vehicles being monitored. The report is a useful resource for state personnel and others involved in the planning and design of highway pavements and structures.

Authors:
Hallenbeck,M. E., Weinblatt,H.

Keywords:
analysis, data, design, highway, pavement, pavements, structures, traffic, truck, volume, Miscellaneous Library

Abstract:
This research was Phase III of field investigations carried out over 12 years at a test section in southwest Washington State in an effort to quantify the contribution of geotextile separators to the long-term performance of pavement sections. Five different geotextile separators, as well as a control (soil-only) section, were installed in a test section covering two lanes with different base course thicknesses on a low volume but heavily loaded rural highway west of Bucoda, Wash. Phase I evaluated the performance of the separators during construction. Phases II and III were conducted to evaluate the performance of the separators 5 and 12 years after construction, respectively. Field and laboratory tests were conducted on the subgrade, granular base materials, and the geotextiles as part of the effort to correlate the performance of the pavement section to the presence of the geotextile separators. Falling weight deflectometer (FWD) testing was also performed at the site as part of the effort to quantify the performance of the pavement section. The laboratory tests indicated that the geotextiles successfully performed their separation function over the 12-year period. However, the soil-only sections had a minimal amount of intermixing at the base course/subgrade interface, indicating that the separation benefits of geotextiles may not be realized under relatively thick pavement sections. Field density tests indicated that the density of the subgrade in the sections with a geotextile generally increased between construction and the first field investigation, whereas the density of the soil-only sections remained about the same. Similarly, the FWD tests showed that the most significant increase in the subgrade moduli occurred in the first few months following construction. However, the soil-only sections exhibited behavior similar to the sections with geotextiles during the FWD testing, suggesting that for the relatively thick pavement sections, incorporation of geotextiles may not have provided a significant contribution to the overall performance of the section over the 12-year period. Some of the FWD results did suggest that geotextiles might contribute to an increase in the base course modulus over time.

Authors:
Collins,B. M., Holtz,R. D.

Keywords:
base, behavior, benefit, benefits, construction, control, density, falling weight deflectometer, field investigations, geotextile, geotextile separators, highway, materials, moduli, pavement, pavement performance, pavement section, research, rural, separators, subgrade, tests, volume, Washington, Washington state, weight, performance

Download Report:

External Links: http://www.wsdot.wa.gov/research/reports/fullreports/595.1.pdf http://wsdot.wa.gov/Research/Reports/500/595.1.htm

Abstract:
The purpose of this research was to explore the relationship between roadway and roadside accidentrates for Washington State highways to improve the Washington State Department of Transportation's(WSDOT) process of modeling roadway and roadside accident rates and to arrive at possible improvements in the efficiency of WSDOT's safety project programming process.The project tested the use of the seemingly unrelated regression estimation (SURE) model to modelthe roadway and roadside simultaneously. The theoretical advantage of the SURE approach is that it does not impose any a priori assumptions on the explicit linkage between roadway and roadside accident rates, and there is no theoretical support for explicit linkage, either. The data used to derive this model were from a random sample of 500 one-mile sections from the Washington State highway system. Traffic dataincluded traffic volumes, truck compositions, AADT, traffic speeds, and other relevant information.Geometric data included lane, shoulder, median, curve, and intersection information. Historical weather data such as monthly precipitation and temperature were collected from the National Oceanic and Atmospheric Administration database.In comparing significant explanatory variables between the roadway accident rate and roadsideaccident rate models, very few variables were common. This confirms that it is preferable to specifyseparate functional forms for roadway and roadside accident rates. Empirical results indicated thatcorrelation between roadway and roadside accident rates was insignificant, indicating that efficiency gainsfrom the SURE model would be minimal. The important finding from a programming standpoint is thatjointly modeling the roadway and roadside simultaneously would not result in significant efficiencyimprovements in comparison to the current state-of-the-practice in Washington State.

Authors:
Chayanan,S., Nebergall,M., Shankar,V., Juvva,N., Ouyang,Y.

Keywords:
roadway, roadside, accident rates, safety programming, research, Washington, Washington state, highway, transportation, WSDOT, modeling, safety, regression, linkage, data, traffic, traffic data, volume, truck, speed, median, temperature, database, models

Download Report:

External Links: http://www.wsdot.wa.gov/research/reports/fullreports/562.1.pdf http://wsdot.wa.gov/Research/Reports/500/562.1.htm

Abstract:
This summary report presents an overview of the level of traveler usage (e.g., how many vehicles use the freeways) and travel performance (e.g., how fast they are traveling, where and how often congestion ocurs) on the principal urban freeways in the central Puget Sound area. The freeways studied in this project are managed by the Washington State Department of Transportation (WSDOT) using its FLOW system, a coordinated network of traffic monitoring, measuring, information dissemination, and control devices that operates on urban state and Interstate highways in the central Puget Sound region. Data presented in this report were collected by the WSDOT's freeway surveillance system. The project that led to this report is intended to meet two separate purposes: 1) to enhance WSDOT's ability to monitor and improve its traffic management efforts on Seattle-area highways, and 2) to provide useful information to the public and decision makers about the status of the freeway system's operational performance. This report is primarily intended to meet the second of these objectives. However, the software developed to assist in freeway data analysis for this project and many of the graphics presented in this report are directly applicable to the first objective.

Authors:
Avery,R. P., Ishimaru,J. M., Nee,J., Hallenbeck,M. E.

Keywords:
analysis, Archived Data User Services (ADUS), congestion, congestion monitoring, control, data, flow, freeway, freeway performance, highway, information dissemination, ITS, management, monitoring, performance, public, research, surveillance, traffic, traffic management, traffic monitoring, transportation, urban, Washington, Washington state, WSDOT

Download Report:

External Links: http://www.wsdot.wa.gov/research/reports/fullreports/563.1.pdf http://wsdot.wa.gov/Research/Reports/500/563.1.htm

Abstract:
To address concerns of resource agencies about the potential impacts of ferry terminal expansion on valuable habitat functions and resource use of nearshore areas, the Pacific Northwest National Laboratory (PNNL), in partnership with the Washington State Department of Transportation (WSDOT), conducted field trials with off-the-shelf products that promote light passage through dock structures. These products included a SunTunnel(TM), deck prisms, and a metal halide greenhouse light. Light measurements (photosynthetically active radiation, PAR), were also recorded beneath glass blocks and a metal grating installed at Clinton Ferry Terminal on Whidbey Island, Washington. A review of other studies measuring the effects of dock shading and alternate dock materials was conducted.PAR measurements from this study were related to minimum requirements for eelgrass Zostera marina photosynthesis and to the known maximum photosynthetic "saturation" rate for Z. marina. We also related PAR measurements to what we know about light requirements for macroalgae and kelp, and light effects on juvenile salmonid feeding and passage under overwater structures. All of the light technologies tested could provide enough light for eelgrass growth underneath a ferry terminal that is being expanded or rebuilt if certain requirements are met. For example, all of the technologies (some signgly and some in multiples) could provide adequate light for eelgrass if the dock is no greater than 15 ft. above the eelgrass and certain air:water ratios are met. At increased distances between the deck and eelgrass, the air:water ratio and total distance light must travel begin to limit the technolgies that could successfully be applied. In general, the products predicted to provide the most to the least light to eelgrass are the grating, SunTunnel, metal halide greenhouse light, and prisms. Light levels required to allow fish to feed and to form schools are low , and much less than those required for photosynthesis (Ali 1959). Based on Ali's data, our research indicates that installing any of the tested light products would likely maintain light levels under the dock above those required for active feeding by juvenile salmonids.

Authors:
Blanton,S. L., Thom,R. M., Borde,A., Diefenderfer,H., Southard,J.

Keywords:
light, overwater structure, nearshore habitat, photosynthesis, salmonids, eelgrass, transportation, highway, port, Washington, research

Download Report:

Abstract:
In this report, we present a novel approach for estimating traffic speed using a sequence of images from an un-calibrated camera. We assert that exact calibration is not necessary to estimate speed. Instead, to estimate speed we use (1) geometric relationships inherently available in the image, (2) some common sense assumptions that reduce the problem to 1-dimensional geometry, (3) frame differencing to isolate moving edges and track vehicles between frames, and (4) parameters from the distribution of vehicles lengths.

Authors:
Dailey,D. J., Cathey,F. W., Pumrin,S.

Keywords:
video image processing, calibration, camera, speed sensor, vehicle length distribution, transportation, highway, research

Download Report:

Abstract:
The SWIFT (Seattle Wide-area for Travelers) project was a field operational test of a wide area ITS communications system using a flexible FM sub-carrier High Speed Data System (HSDS). The test was conducted in a partnership with WSDOT, King County Metro Transit, Delco Electronics, Inc., IBM, Seiko Communications Systems, Metro Traffic Control and the Federal Highway Administration. Three devices were used, by the public, to receive the traveler a Delco car radio (capable of providing vector navigation in addition to personal paging and the messages); a Seiko wrist watch pager; and a portable computer (capable of providing graphic displays of traffic advisories and bus positions). After the 15-month test, interviews with the 600 Seattle commuters/participants were conducted to assess user acceptance. A communications study evaluated the adequacy of the HSDS system to disseminate traveler information. Architecture study assessed the effectiveness of the various components to carry out SWIFT operations. institutional issues study documented the history of the project and assessed the institutional issues confronted. A deployment cost study investigated the cost of deployment of a SWIFT system and assessment of potential profitability. The first five reports in this series detail individual aspects of the project.

Authors:
Wetherby,B., Perez,W.

Keywords:
Acceptance, Assessment, bus, computer, control, cost, counties, data, Deployment, effectiveness, evaluation, highway, Institutional, interviews, Issues, ITS, Miscellaneous Library, paging, portable computer, project, public, seattle, speed, Study, SWIFT, System, systems, traffic, traffic advisories, traffic control, transit, traveler information, WSDOT

Download Report:

Abstract:
Funded by the 1987 Intermodal Surface Transportation Efficiency Act, the Strategic Highway Research Program (SHRP), was a five year, $150 million research program to improve the performance of the nation's roads by addressing four key areas: concrete and structures; highway safety and maintenance; asphalt; and long-term pavement performance. Nearly one-third of the $150 million was allocated for the study of asphalt, specifically to develop performance based specifications that would relate material properties of the binder and the mix to field performance. Superpave (Superior PERforming asphalt PAVEments) encompasses the products of the SHRP asphalt research program and consists of three interrelated elements: an asphalt binder specification with supporting tests; a mix design and analysis system with supporting tests; and performance prediction models. This report is a compilation and synthesis of Washington DOT's (WSDOT) experience with selected components and concepts of the SHRP/Superpave technology to include the following: performance graded (PG) binder usage and specification validation; gyratory mix design; the Superpave Shear Test (SST); and field performance of the Superpave mixes.Binders typically specified by WSDOT (AR400OW and PBAs -2, -5, -6. -6GR) were classified in terms of five Superpave performance grades: PG 58-22; 64-22; 64-28; 64-34; and 70-28. Although data from 171 weather stations suggest that as many as 6 low- and 5 high-temperature grades could be specified, binder availability and regional pavement distress were used to develop guidelines for statewide PG usage. Three binders were recommended for use in the western, northeastern and southeastern regions of the state as follows: PG 58-22; PG 58-34; and PG 64-28, respectively. Validation of the binder specification with respect to low temperature cracking was accomplished using binder and field performance data from 28 projects. The results were very encouraging: the original SHRP algorithm for binder selection correctly "predicted" field performance in 22 of 28 cases, whereas the LTPP algorithm for binder selection correctly "predicted" field performance in 26 of 28 cases.Additionally, a laboratory experiment using the Superpave Shear Test (SST) apparatus was undertaken to test the effectiveness of binder "bumping," i.e., increasing the high temperature grade because of exceptionally high traffic volume and/or slow or standing traffic. The data clearly indicate that the SST is an effective tool for discriminating between binders and that 'bumping" may be effective in reducing pavement rutting. Permanent shear strain for specimens made with a PB 70-xx binder was only 25 to 33% of the shear strain for specimens made with a PG 58-xx binder.As originally configured, the Superpave mix design matrix included seven traffic levels and four temperature regimes for 28 possible compaction levels. Recognizing that the 28 compaction levels made for a somewhat unwieldy system, WSDOT attempted to reduce the number of compaction levels by conducting a series of mix designs at each compaction level. The results of the limited experiment suggest that it might be possible to limit the number of compaction levels required for mix design. Research by Brown et. al. (NCHRP 99) tends to confirm this as they have suggested reducing the number of compaction levels and provided more definitive guidance with respect to each level.Since 1993 WSDOT has place 44 projects which include some component of the Superp ave technology. For 17 of these projects parallel Hveem and Superpave mix designs were conducted. In 13 of the 17 cases, the Superpave design asphalt content was equal to or greater than the Hveem design asphalt content, though the difference was usually no more than 0.2%. A fundamental difference between Hveem and Superpave mix design methods is the compaction device. Data from these field projects indicate that the current kneading and gyratory compaction protocols (at least for 109 gyrations) yield similar air void contents.As noted previously, Washington DOT has placed 44 projects which involve some component of the Superpave technology. For 18 of the projects a conventional Hveem mix design was conducted using a PG binder (Hveem-PG). The remaining 26 projects were truly Superpave, i.e., the materials selection and mix design were established in accordance with the Asphalt Institute's SP2, Superpave Level 1 Mix Design. According to WSDOT practice the following numerical indices trigger maintenance: Pavement Structural Condition (PSC) 10 mm; or International Roughness Index (IRI) > 500 cnVkm. Although relatively "young", the 44 projects are performing quite well. The average values of rutting, PSC, and IRI (4, 91, and 121, respectively) are all well below the "trigger" values. With respect to rutting and PSC, the performance of Hveem-PG and Superpave projects is virtually identical. However, the ride quality of the Superpave projects is a bit rougher than the Hveem-PG binder projects: IRI of 134 for the former and 103 for the latter. The higher values of IRI measured on the Superpave projects may be the result of the typically coarser aggregate gradation or differences in construction techniques.WSDOT's Superpave experience has not been without challenges. Still, its overall experience has been very encouraging. Experimentation with the revised compaction matrix, continued use of the SST, field validation of the "bumping" experiment, and long-term monitoring of field performance will provide the necessary data to allow WSDOTs critical assessment of Superpave's technical merit and economic viability.

Authors:
Leahy,R. B., Briggs,R. N.

Keywords:
SHRP, Superpave, asphalt, intermodal, transportation, transportation efficiency, highway, research, program, performance, concrete, structures, highway safety, safety, maintenance, pavement, specifications, specification, asphalt pavement, pavements, tests, design, analysis, prediction, models, Washington, WSDOT, data, temperature, cracking, LTPP, traffic, volume, compaction, materials, condition, international roughness index, roughness, index, ride quality, quality, aggregate, construction, ITS, monitoring

Download Report:

Abstract:
This report concludes the four phase evaluation of Washington's fee and fine system. The primary focus of this report is the occurrence and capture of overweight vehicles at three selected evaluation sites in the Eastern Washington: Pasco, Chattaroy, and Cashmere. Weigh-in-motion data was utilized to determine any changes which occur in truck traffic when weight stations are open and closed. Violation rates are estimated between 20% and 22% with capture rates between 20% and 27%, depending on the site. Violation and capture rates, in addition to truck volume and axle weights, are further calculated for different truck types during all hours of the day. The analysis also includes seasonal variations in all variables.

Authors:
Jessup,E. L., Casavant,K. L.

Keywords:
highway, violation, capture, season

Download Report:

Abstract:
The objective of this paper was to address the problem of the accelerated highway and bridge deterioration from overloaded trucks by developing a profile of trucks which exceed overweight permit authorization. The profile of trucks in violation of overweight permits include location, seasonal variation, commodity group, origin/destination, scale type, and permit type. The profile was developed from a statewide telephone survey of permit violations between November 1, 1991, and October 31, 1992, and provide policy makers, transportation planners and law enforcement officials greater understanding of the nature of load related damage created by overload permit violations.

Authors:
Casavant,K. L., Barron,C. J., Jessup,E. L.

Keywords:
highway, overweight, truck, permits, fines, profile

Download Report:

Abstract:
The main objective of this study was to determine the effectiveness of Washington's fee and fine system in recapturing the physical and resultant financial damage to pavements caused by overload vehicles, through the court and legal process. This was accomplished through interviews with weight enforcement officials and court personnel in addition to a detailed examination of over 8,000 citations from nine counties between September 1991 and August 1992. The results provide a complete examination of Washington's fee and fine system and help identify weakness in the system.

Authors:
Barron,C. J., Jessup,E. L., Casavant,K. L.

Keywords:
truck, overweight, highway, permits, fines, fees, court

Download Report:

Abstract:
The objective of this study was to determine the degree of participation in road weight enforcement programs for cities and counties in the state of Washington. This is accomplished through the use of a survey to cities and counties throughout the state.The results indicate that larger cities and more urban counties have greater involvement in weight enforcement programs, whereas smaller cities and more rural couties have less involvement. Only six cities in the state were directly involved in weight control enforcement programs with Seattle and Tacoma having the most active programs. Eleven of the 39 counties in the state were identified as having full weight enforcement programs and 5 counties having only partial weight enforcement programs.

Authors:
Barron,C. J., Jessup,E. L., Casavant,K. L.

Keywords:
highway, overweight, truck, permits, fines, fees, court

Download Report:

Abstract:
Dames & Moore And their subcontractor, Inco Engineers, have prepared this Manual of Practice for conducting bridge foundation-soil interaction analyses. The manual is intended to assist engineers in the Bridge Design office at the Washington State Department of Transportation (WSDOT) who perform dynamic analysis of bridge-foundation systems. The primary purpose of the manual is to present practical and accurate methods of estimating the foundation stiffness matrices for abutment or pier foundations supported on footings or piles. These matrices are needed for soil-structure interaction analysis to more accurately determine the seismic loads acting on the bridge superstructure and on the abutment and pier foundations.This Manual of Practice consists of two volumes. Volume I presents five bridge example problems:1. Coldwater Creek2. Deadwater Slough3. Ebey Slough4. Northup Way5. FHWAThe first four examples are actual WSDOT bridges and the fifth example is a fictitious bridge that appeared in a 1991 FHWA course notebook on seismic design of highway bridges.Volume II presents the input and output files of the SEISAB computer program for the dynamic soil-structure interaction analysis of bridges. The SEISAB computer program is currently used by WSDOT in the seismic design of Washington state bridges.Dames & Moore recommends the FHWA and Novak methods to estimate bridge foundation stiffness matrices. These methodologies are presented in detail in the Coldwater Creek example problem in Volume I. In this example, the basic theory and relevant equations or inputs for implementing these methodologies are provided first and are immediately followed by their application to the Coldwater Creek bridge. The appropriate equations or inputs from the FHWA and Novak methodologies presented not the Coldwater Creek example problem are identified and applied in the other four bridge example problems. Volume I also contains three appendices. The basis for the recommendation of the FHWA and Novak methods is provided in Appendix A, which is a reproduction of the 1992 Dames & Moore report to WSDOT on the evaluation of methods to estimate foundation stiffnesses. Appendix B consists of selected pages from the BMCOL 76 computer program user guide; this computer program, which computes the load-deflection and moment-rotation curves for single piles, is part of the FHWA methodology. Appendix C presents the method for transforming the foundation stiffness matrices from one coordinate system to another. This transformation process is important because the coordinate systems assumed in the FHWA and Novak methods are generally different and therefore are not necessarily the same as the SEISAB coordinate system. Coordinate transformations are also discussed in the ColdWater Creek example problem.

Authors:
Dames & Moore- Inca Engineering

Keywords:
analysis, bridge, bridge design, bridge foundation, bridges, computer, computer program, design, equations, evaluation, Foudation-Soil, foundation, foundation stiffness, highway, interaction, loads, manual, methodology, methods, piles, program, seismic, seismic design, soil-structure interaction, superstructure, System, systems, transportation, volume, Volumes I & II, Washington, Washington state, WSDOT

Download Report:

Abstract:
This report summarizes an investigation of the technical aesthetic, and economic feasibilities of incorporating special noise barrier applications into a highway noise control program. The intent of the report is to take as a starting point the thin, vertical, reflective barrier now used in most applications. Special barrier applications are those beyond the thin vertical reflective barrier.The investigation of technical feasibility relates to the formulation of the effects of absorptive treatments, slanted tops, T-tops, and other special applications. The economic and aesthetic feasibility investigations examine the value of employing these special applications in lieu of thin, vertical, reflective barriers. The research reported on herein was performed on behalf of the Washington State Department of Transportation. The intent of the was for background studies of the effects of special treatments, so the could be in a position to implement pilot projects at a later date.

Authors:
Cohn,L. F., Harris,R. A.

Keywords:
absorption, absorptive, applications, barrier, barriers, control, highway, Insertion Loss, noise, parallel barrier, program, project, research, transportation, Washington, Washington state

Download Report:

Abstract:
The major objectives of this study were to examine: (1) the types of recycled materials that are appropriate and feasible as alternative paving materials such as glass and tires; and (2) the types of recycled materials, such as mixed-plastics and compost, that can be utilized in all types of transportation applications other than pavements. Seven key products are investigated: tires; glass; asphalt concrete fly ash; compost; mixed plastics; and sign stock. Performance and cost data for pavements is documented for both in-state and nationwide applications. The national experience \'with the use of waste glass as an additive to asphalt concrete and its use in unbound base material is so highlighted. Programs for experimental use of recycled material are outlined. Recommendations for staffing and program changes to deal with recycling are also discussed.

Authors:
Swearigen,D. L., Jackson,N. C.

Keywords:
additive, Alternative, applications, asphalt, asphalt concrete, base, base materials, concrete, construction, cost, data, experimental, fly ash, Glasphalt, highway, highway construction, ITS, materials, objectives, pavement, pavements, performance, program, recycled ACP, recycling, Rubber-asphalt, tire, tires, transportation

Download Report:

Abstract:
This final report demonstrates the feasibility of employing high molecular weight/high density polyethylene cylinders as the energy dissipating medium in highway safety appurtenances. It is shown that this polymer can dissipate large amounts of kinetic energy, undergo large deformations and strains without fracturing, and essentially restore itself to its original size, shape, and energy dissipation potential when the forcing function is removed.This research involves a quasi-static and impact loading experimentalinvestigation to determine the energy dissipation characteristics of HMW HDPEtubes as functions of temperature, radius to wall thickness ratio, strain,strain-rate, deformation, and repeated and cyclic loading. The results ofthis experimental program are analyzed to develop analytic energy dissipationexpressions which are then employed in the design of truck mountedattenuators (TMA), Finally, an expert system computer program, CADS, ismodified to use HMW HDPE tubes in the generalized design of crash cushions.The potential financial, legal, and safety payoffs for highway operationsassociated with developing highway safety devices which are essentiallymaintenance free are significant. Maintenance costs associated with therepair of impacted safety devices would be greatly reduced or eliminated.Tort liability exposure related to damaged or collapsed hardware would besignificantly decreased. Finally, the safety of the motoring public and themaintenance personnel involved in maintaining and repairing damaged hardwarewould be enhanced.

Authors:
Carney III,J. F.

Keywords:
computer, computer program, cost, costs, cyclic loading, density, design, development, Energy, experimental, expert system, exposure, highway, highway safety, impact, impact attenuation devices, ITS, maintenance, maintenance free, polyethylene, polymer, program, public, research, reusable, safety, self-restoration, strains, temperature, truck

Download Report:

Abstract:
Various methods of controlling traffic through construction zones are examined. The accident statistics concerning construction flagging are summarized, indicating the need for improvements in construction flagging techniques. A research methodology is presented for implementing and evaluating several flagging techniques.

Authors:
Hinze,J., Ifie,A. O.

Keywords:
construction, construction flagging, evaluation, flagging techniques, highway, highway construction, methodology, research, statistics, traffic, traffic control

Download Report:

Abstract:
The Washington State Department of Transportation will be conducting experimental field testing of several selected ploymer concrete thin overlays over a ten-year period. The ploymer concrete material is manufactured by private industry firms and installed on selected bridge decks under standard WSDOT construction contracts. Approximately 14 bridges will be involved in the experiment.The study was conducted in cooperation with the U.S. Department of Transportation, Federal Highway Administration. The Washington State Department of Transportation will be conducting field testing of several selected concrete thin overlays over a ten-year period. The polymer concrete material is manufactured by private industry and installed on selected bridge decks under standard WSDOT construction contracts. 14 bridges will be involved in the experiment. The Snake River Bridge at Clarkston, Washington, Bridge No. 12/915, is the first bridge of the to receive a 1/4 thin overlay. The polymer concrete used is by Polycarb. The deck was repaired and overlaid in June of 1986. Work on the thin overlay began on June 8 and was completed on June 20. A total of 6,477 S.Y. of overlay was involved. Traffic was accommodated at all times on the portion of the bridge not being overlaid. Construction progressed relatively smoothly per the inspector\'s report. The material permitted the contractor flexibility in the rate of installation and in starting and stopping the work. Width of installation was varied to accommodate temporary traffic lanes. Pavement skid tests and bond tests all proved satisfactory. Ninety-one percent of the resistivity tests exceeded the minimum required by the specifications. The majority of the test points that did not meet the minimum specified occurred at the beginning of the work, where the contractor attempted to apply the material with spray that apparently did not provide accurate proportionate mix of the epoxy components. Subsequent tests and reports delamination, half-cell, chloride content, and rutting values to the original deck survey values.

Authors:
Roper,T. H., Henley,E. H. Jr

Keywords:
bridge, bridge deck, bridge deck repairs, bridge decks, bridges, chloride, concrete, construction, contracts, Epoxy, experimental, half-cell, highway, lanes, overlay, overlays, pavement, polymer, polymer concrete, specification, specifications, survey, tests, thin overlay, traffic, transportation, Washington, Washington state, WSDOT

Download Report:

Abstract:
This is the final report of PlusRide being used as the wearing course on a bridge deck overlay.A Class D Asphalt Concrete pavement which is an open graded friction course was used on an adjacent bridge as a control for the PlusRide. The PlusRide claims were high friction resistance, reduced noise, increased fatigue properties and deicing characteristics. The PlusRide cost 50 percent more that the Class D and the friction resistance, noise levels and fatigue properties were the same for the PlusRide and Class D. The deicing characteristics could not be confirmed due to the absence of surface icing on highways in the Yakima area.

Authors:
Peters,A. J., Schultz,R. L.

Keywords:
asphalt, asphalt concrete, Asphalt Concrete pavement, asphalt pavement, bridge, bridge deck, bridge deck overlay, claims, Class D, concrete, control, cost, Deck, fatigue, friction, highway, Highways, noise, overlay, pavement, PlusRide, resistance

Download Report:

Abstract:
A Highway Advisory Radio (HAR) system was installed on I-90, Snoqualmie Pass to inform motorists of winter driving conditions. Despite numerous operational problems with equipment, the service has been well received by the traveling public. The system was found to have an added benefit during the summer months as an information system to alert motorists of delays or other problems caused by construction activities. The HAR system on Snoqualmie Pass has been expanded and additional systems have been installed in the Seattle area to inform motorists of construction activities.

Authors:
Krug,H. O.

Keywords:
benefit, condition, construction, HAR, highway, Highway Advisory Radio, public, seattle, systems, winter, winter driving

Download Report:

Abstract:
This report is designed to provide information to guide inspectors of wood highway structures in the use of stress wave inspection technology. It explains the methods and instruments used to measure the velocity of stress waves (sound) in wood. The characteristic behavior of sound waves in wood of various species, moisture content, preservative treatment and infection by wood destroying organisms is described. The important effects of the anatomy of wood and the orientation of grain and annual rings to the wave path are discussed to aid in the interpretation of measurements. Characteristics of the instrumentation essential to its calibration are explained and instruction is provided in the appropriate use of these tools. This report has been written to serve as a manual for \"on site \" stress wave inspection of the kind of wood structures found in highway systems. It is a compendium or experience in the field inspection of many wood buildings and highway bridges. Original research conducted to fill in voids in the published studies, is described in the Appendices.

Authors:
Hoyle,R. J. Jr, Rutherford,G. S.

Keywords:
behavior, bridge, bridges, calibration, grain, highway, insect damage, inspection, ITS, manual, nondestructive testing, research, sound waves, Stress waves, stresses, structures, systems, technology, termite damage, velocity, wood decay

Download Report:

Abstract:


Authors:
Horner,R. R., Kortenhof,M.

Keywords:
environmental, highway, erosion, pollution control

Abstract:
This study involved an in-depth evaluation of the Washington State Department of Transportation highway data development and analysis activities. It developed statistically-based procedures and recommendations for a streamlined highway data collection program. Opportunities to reduce manpower and equipment costs, streamline work activities, improve the quality of data collection and provide accurate and timely data for the various users were identified. Given the focus on highway data, the major effort was devoted to the Department's traffic counting program. However, many data items and programs were considered, with the following receiving particular attention: traffic volume counting, including estimation of annual average daily traffic at any location throughout the state highway system; associated seasonal, axle and growth factors; vehicle classification; truck weights; and the relationship between the statistical sampling requirements recommended for these items and those associated with the FHWA Highway Performance Monitoring System in the state.

Authors:
Ritchie,S. G., Hallenbeck,M. E.

Keywords:
analysis, Annual, axle, cost, costs, data, data collection, developed, development, equipment, evaluation, highway, monitoring, performance, performance monitoring, program, quality, sampling, seasonal, Study, System, traffic, traffic counting, transportation, truck, vehicle classification, volume, Washington, Washington state, weight, weights

Download Report:

Abstract:
The Washington State Department of Transportation (WSDOT)/University of Washington Highway Runoff Water Quality research project, conducted from 1977 to 1982, produced a number of results of potential use to WSDOT. An effort was required to implement these results in the Department's procedures. One phase of implementation completed previously involved preparation of a guide for assessing the impacts of operating highways on aquatic ecosystems and training WSDOT personnel in its use. The present phase involved formulating decision criteria in a number of water quality problem areas of concern to WSDOT and determining the need for revisions to department documents for consistency with the research results and the new criteria. The results of this phase are presented in a two volume implementation manual and a separate document listing the suggested modifications to four existing WSDOT manuals. Volume 1 of the implementation manual state the criteria, which were developed for: 1) identification of waters potentially sensitive to impact by operating highways; 2) the use of vegetated drainage courses to treat highway runoff; 3) the use of retention/detention facilities for highway stormwater drainage; 4) disposal of ditch cleaning spoils; 5) the use of woodwaste fills for highway construction; 6) highway sanding; 7) dilution of highway runoff in a receiving water; 8) highway cleaning; and 9) stream channel modification for highway construction. Volume 2 presents the basis of each criterion listed in volume 1, including references to the research results and other literature, the rezoning followed, development of equations, etc.

Authors:
Horner,R. R.

Keywords:
environmental, highway, stormwater, water pollution, criteria, environmental impact, mitigation, Washington state, research implementation

Download Report:

Abstract:
The Washington State Department of Transportation (WSDOT)/University of Washington Highway Runoff Water Quality research project, conducted from 1977 to 1982, produced a number of results of potential use to WSDOT. An effort was required to implement these results in the Department\'s procedures. One phase of implementation completed previously involved preparation of a guide for assessing the impacts of operating highways on aquatic ecosystems and training WSDOT personnel in its use. The present phase involved formulating decision criteria in a number of water quality problem areas of concern to WSDOT and determining the need for revisions to department documents for consistency with the research results and the new criteria. The results of this phase are presented in a two volume implementation manual and a separate document listing the suggested modifications to four existing WSDOT manuals. Volume 1 of the implementation manual state the criteria, which were developed for: 1) identification of waters potentially sensitive to impact by operating highways; 2) the use of vegetated drainage courses to treat highway runoff; 3) the use of retention/detention facilities for highway stormwater drainage; 4) disposal of ditch cleaning spoils; 5) the use of woodwaste fills for highway construction; 6) highway sanding; 7) dilution of highway runoff in a receiving water; 8) highway cleaning; and 9) stream channel modification for highway construction. Volume 2 presents the basis of each criterion listed in volume 1, including references to the research results and other literature, the rezoning followed, development of equations, etc.

Authors:
Horner,R. R.

Keywords:
environmental, highway, stormwater, water pollution, criteria, environmental impact, mitigation, Washington state, research implementation

Download Report:

Abstract:
TThe effectiveness of Swareflex Wildlife Reflectors in reducing deer-vehicle collision rates was tested on 395 in eastern Washington State where high mortality rates of white-tailed deer (Odocoileus virginianus) had previously been recorded. Reflectors were placed in four test sections and alternately covered and uncovered at regular intervals during the late fall to early spring period from 1981 to 1984. During this period, 52 deer were killed at night in test sections when the reflectors were covered and six deer were killed at night when the reflectors were uncovered. This difference in deer-vehicle collision rates between the covered and uncovered periods is significant indicating that the reflectors were effective on this highway

Authors:
Schafer,James, Carr,William P., Penland,Stephen

Keywords:
collision, effectiveness, highway, mortality, Odocoileus virginanus, reflector, road-kill, Swareflex, Washington, Washington state, White-tailed deer, wildlife

Download Report:

Abstract:
This report present the final form of the Washington State Highway runoff pollutant loading model, incorporating data from the five years of study. It also features a probabilistic analysis of concentration and loading data designed to express the chance of exceeding specific values in a given case. Other topics include further assessment of the toxicity of highway runoff and its causes and mitigation.

Authors:
Little,M. L., Horner,R. R., Mar,B. W.

Keywords:
analysis, Assessment, data, highway, highway runoff, ITS, mitigation, model, pollutant loading, runoff, stormwater, Toxicity, Washington, Washington state

Download Report:

Abstract:
A study of recreational vehicle waste disposal at highway rest areas was conducted from RV wastewater is significantly stronger than wastewater in BOD, COD, and suspended solids. It also contains preservative compounds, most of which contain formaldehyde or a formaldehyde derivative. With adequate dilution, these wastes should not interfere with waste by mixed cultures of aerobic or anaerobic bacteria or There that waste treatment facilities be affected by improper use of the disposal stations, such as for disposal of hazardous wastes. In addition, improper use may lead to temporary unsanitary conditions around the station. Equations to estimate disposal station use and loading factors, and design equations for treatment of wastes are presented. The public perceives the stations to be and cost-effective provided they are paid for by RV owners. RV owners are willing to pay an annual fee which will cover the costs of construction, operation and maintenance of the stations.

Authors:
Kiernan,K., Brown,C., Benjamin,M., Ferguson,J. F.

Keywords:
Annual, biological waste treatment, condition, construction, cost, cost effective, costs, design, disposal, equations, facilities, fee, Formaldehyde Toxcity, Hazardous, hazardous wastes, highway, maintenance, public, recreational vehicles, rest area, rest areas, Study, suspended solids

Download Report:

Abstract:
Statewide sampling of highway runoff continued through 1980-81, and the resulting data has been aggregated with that from previous years to further investigate pollutant loadings. Results have validated the solids loading model previously proposed by Asplund (1980) for Western Washington Highways and tentatively extended the model to Eastern Washington. Loading of there pollutants can be predicted from total suspended solids loading using ratios derived from the data. These ratios may be taken as constants at any Washington State location for some pollutants or as linear functions of traffic or other contaminants. Comparison of runoff from a sulfur-extended asphalt pavement with runoff elsewhere indicates higher sulfate loads in the former case. A limited sampling program along an uncurbed highway section observed higher pollutant concentrations from these sections to curbed areas. Sampling of solids adhering to the undercarriage of automobiles produced widely varying results but suggested that vehicles traveling on rural or unpaved roads accumulate significant amounts of solids that can be released on highways. The final year of field sampling will concentrate on improving the loading models, especially for Eastern Washington application, and continuing the sulfur extended asphalt study with a functional control site experiencing the same conditions.

Authors:
Tai Wik,David Chui, Mar,B. W., Horner,R. R.

Keywords:
analysis, asphalt, asphalt pavement, Concentrations, condition, control, data, extended asphalt, highway, highway runoff, Highways, loads, model, models, pavement, pollutant loading, Pollutants, program, runoff, rural, sampling, statistical analysis, sulfur, suspended solids, traffic, Washington, Washington state

Download Report:

Abstract:
The Motor Carrier Act of 1980 and the Staggers Act of 1980 have partially set aside decades of rigid regulations of interstate freight movement. These actions have the potential to bring forth significant changes to the networks of interstate freight transportation. The object of this research was to ascertain the impacts of deregulation of the Washington State transportation system. Information was obtained by surveying and interviewing shippers and freight transportation providers throughout the state. Anticipated impacts, e.g. accelerated rail abandonment or lost of motor carrier service to small communities were not present. The study reflects a relative increase in truck service and decrease in rail service since deregulation. Indications are this may be further amplified in certain regions of the state. The study recommends that potential highway impacts be incorporated into pavement management systems. Transportation officials are enjoined to treat issues relative to truck size and weight, highway cost allocation and deregulation as a single issue. Also, the Local Rail Service Assistance Program should be considered for use to offset any adverse impacts resulting from deregulation. During this period of the study, general economic conditions were poor. This resulted in a decrease in freight shipments and would suggest that some impacts of deregulation have been suppressed.

Authors:
Public Transportation and Planning Division, Washington State Department of Transportation

Keywords:
condition, cost, Deregulation, freight, highway, highway impacts, impact, impacts, management, management system, management systems, motor carrier, networks, pavement, pavement management, pavement management systems, program, rail service, railroads, regulation, research, System, systems, transportation, truck, trucking, trucks, Washington, Washington state, weight

Download Report:

Abstract:
This small car accident study investigated accidents in Washington State in four passenger car categories: subcompact, compact intermediate, and large. The primary purpose of the study was to evaluate the effects on safety of increases in the number of smaller cars on the highways. Traffic accident data for the period 1973-79 were analyzed to determine the accident severity for the different automobile classes, and this analysis showed that the smaller vehicles had a higher proportion of fatal and injury accidents that the other categories.The, accident data for 1980 were used to compare accident experience with regard to injury class of the occupants, roadway surface conditions, roadway character, light conditions, collision type, objects struck, and location of accident. Analysis showed that for total accidents per one thousand registered vehicles, the large cars had a higher rate (68) than either the subcompacts (43), compacts (45), or intermediate size vehicles (46). However, the subcompacts and compacts had higher percentages of fatalities and serious injuries to their occupants, and a higher proportion of such accidents occurred on wet, snowy, and icy surfaces. In addition, the smaller passenger vehicles had a higher incidence of overturning and rear-end accidents. The analysis suggests there will be significant increases in fatal and injury accidents in future years as the number of smaller vehicles increases. Thus, the report contains recommendations for changes in highway and vehicle design that will modify these adverse trends and reduce injuries and fatalities among drivers and passengers.Some of the recommendations can be implemented fairly quickly, but others will take longer. However, until changes are made, the accident severity for small cars will continue at a level above that for larger automobiles.

Authors:
Public Transportation and Planning Division

Keywords:
accident severity, accidents, analysis, collision, condition, data, design, highway, Highways, light, overturning, roadway, safety, Study, traffic, traffic accident data, Washington, Washington state

Download Report:

Abstract:
The impacts of storm water runoff from Washington State freeways on aquatic ecosystems were investigated through a series of bioassays utilizing algae, zooplankton and fish.Algae and zooplankton were adversely affected by the soluble fraction of the runoff, while suspended solids caused high mortalities of rainbowtrout fry . In addition,. BOD 5 values similar to those reported in the storm water literature were measured; however, there were indications that results were influenced by toxicity to microbial populations.

Authors:
Portele,G., Mar,B. W., Horner,R. R., Welch,Eugene

Keywords:
Algae, Biochemical Oxygen, Biomass, control, Demand, fish, freeway, heavy metals, highway, highway runoff, impact, impacts, Interim, metals, population, runoff, stormwater, suspended solids, Toxicity, transport, Washington, Washington state, Water Pollutants, Washington State Monitoring, zooplankton

Download Report:

Abstract:
A highway storm water runoff pollutant loading. model has been developed based on results from con3posire sampling of approximately 600 storms at nine locations in the State of Washington over five years. The model expresses total suspended solids (TSS) loading in proportion to the product of highway segment length, average runoff coefficient, and vehicles traveling during storm periods. It was dem-onstrated that loadings of contaminants such as chemical oxygen demand, nutrients and trace metals could be estimated from TSS loadings using ratios derived from the data, The model described was developed and validated for assessing total loadings over a time span encompassing a number of storms (monthly or annually). To predict pollutant concentrations and loadings in runoff from a given storm, cumulative distributions were plotted and analyzed to determine the probability of exceeding specific concentration and loading values in a given case. Bioassay studies using highway runoff indicated toxicity to aquatic life when elevated metals deposition from high traffic volumes (in excess of 10,000 -20,000 vehicles per day) or high metals concentrations in rainfall caused runoff concentrations to exceed lethal levels. Draining highway runoff through grass channels 60 meters in length greatly reduced TSS and metals concentrations and the consequent toxic effects. The major product of this research is a guide to assessing and mitigating the impacts of highway runoff to receiving waters.

Authors:
Mar,B. W., Horner,R. R., Spyridakis,D. E., Welch,E. B.

Keywords:
Assessment, Channel, Chemical, Concentrations, data, demand, deposition, developed, highway, highway runoff, impact, impacts, Loadings, Highway runoff, metals, mitigation, model, models, pollutant loading, Pollutants, quality, rainfall, research, runoff, sampling, span, stormwater, suspended solids, Toxicity, traffic, traffic volumes, volume, Washington, Washington state, water quality

Download Report:

Abstract:
This report summarizes the placement and performance of sulfur extended asphalt (SEA) paving mixtures at a highway test site (SR 270) near Pullman, Washington. The report includes a summary of the mixture and structure designs and construction details. This is followed by a discussion of the data collection and analysis accomplished over a three year evaluation period (1979 - 1982). A major experimental feature of the study was the use of 0/100 (conventional asphalt concrete), 30/70 and 40/60 SEA binder ratios (sulfur/asphalt ratios are expressed as weight percents) in the experimental paving mixtures.

Authors:
Mahoney,J. P.

Keywords:
analysis, asphalt, asphalt concrete, asphalt pavement, concrete, construction, data, data collection, data collection and analysis, design, evaluation, experimental, extended asphalt, highway, mixture, pavement, pavement performance, performance, Study, sulfur, Washington, weight

Download Report:

Abstract:
This executive summary overviews the placement and performance of sulfur extended asphalt (SEA) paving mixtures at a highway test site (SR 270) Width3Width8608Width3Width8608 near Pullman, Washington. This is the sixth and last report of this study.

Authors:
Mahoney,J. P.

Keywords:
asphalt, asphalt pavement, Executive, Executive Summary, extended asphalt, highway, mixture, pavement, performance, Study, sulfur, Washington

Abstract:
In high growth areas, highways frequently become congested as the result of land use changes. Local use controls have not prevented the adverse impacts. Further, state funds are inadequate to address the critical problems in growth areas. This study investigates six study areas in Washington compare land use change impacts and the effectiveness of the various procedures applied to prevent or correct such problems and to fund highway improvements in growth areas. A survey of practice in other states provides information concerning their approaches to the problem. The study concludes that comprehensive land use planning supported by inter-agency cooperation has been ted. Local governments have applied a number of innovative techniques for financing local roads and streets. Cooperative interagency planning before growth is out of control has benefited both the local jurisdiction and the state. However, state and local jurisdictions lack the authority to apply these techniques to state highways in Washington State. The study makes recommendations for increasing interagency cooperation and for legislative remedies.

Authors:
Jacobson,Robert

Keywords:
control, effectiveness, facilities, highway, highway financing, Highways, impact, impacts, improvement, Interagency planning, land use, land use controls, land use planning, land-use, land-use/transportation planning, local government, mitigation, planning, planning coordination, Study, survey, Washington, Washington state

Download Report:

Abstract:
A five-year study was performed to compare conditions in the Pilchuck River before and after channel reconstruction associated with rerouting highway SR-2. The study focused on sediment particle-size analyses, benthic macroinvertebrates and fish. Substrates comparable le to control areas developedin all portions of the new channel within one year after construction. The available data on invertebrates and fish gave no indication of deterioration in diversity, quantity or size in the reconstructed channel. The report provides recommendations for further improvements in the design of stream channel changes should there be no alternative to their construction.

Authors:
Horner,R. R., Welch,Eugene B.

Keywords:
Alternative, Benthic Macroinvertabrates, accident rates, Channel, condition, construction, control, data, design, deterioration, fish, highway, impact, impacts, improvement, Interim, reconstruction, rivers, sediments

Download Report:

Abstract:
Experiments were conducted at four locations to determine if plants grown in biodegradable tube containers or standard types of containers would have higher survival rates than bare root grown plant material. Season of planting was also evaluated. Results indicated that bare foot grown plant material had higher survival rates than container grown material. Spring planting was more successful than fall planting.

Authors:
Rosenthall,R., Wirsing,M. J.

Keywords:
Biodegradable containers, highwa, highway, Landscape plant establishmen, plant surviva, revegetatio, Right-of-way, seaso, season, tubeling

Download Report:

Abstract:
This report summarizes findings detailed in Report Nos. 4 and 5 plus the work of Zawlocki on trace organics in highway runoff. Several hundred compounds tentatively, identified by GC-MS were grouped into nine categories, which were not mutually exclusive. Major components of-these 'categories were petroleum products used by vehicles and incompletely combusted hydrocarbons. The concentrations of these trace organics groups were low compared to criteria proposed for protection of aquatic life.

Authors:
Mar,B. W., Ferguson,J. F., Welch,E. B.

Keywords:
Concentrations, construction, criteria, group, highway, highway runoff, Highways, hydrocarbons, Leachate, Organics, petroleum, protection, quality, runoff, Water Pollutants, Washington State Monitoring, water quality, Woodwaste fills

Download Report:

Abstract:
This report summarizes the placement of sulfur extended asphalt (SEA) paving mixtures at two test sites near Pullman, Washington. One site was on an existing state highway and the other made use of the Washington State University Test Track. The report includes the preliminary mix designs, pavement thickness determination, construction details and initial performance data for the test pavements. A major experimental feature of the study was the use of 0/100 (conventional asphalt concrete), 30/70 and 40/60 SEA binder ratios in the experimental paving mixtures.

Authors:
Mahoney,J. P., Christensen,D. R., Terrel,R.

Keywords:
asphalt, asphalt concrete, asphalt pavement, concrete, construction, data, design, evaluation, experimental, extended asphalt, highway, mixture, pavement, pavement evaluation, pavement performance, pavements, performance, Study, sulfur, test track, Washington, Washington state

Download Report:

Abstract:
While gasoline represents one-third of all hazardous materials transported in the country by trucks, the risk associated with gas transportation, as viewed by the private sector, is small. Public perceptions of risk are much greater due to lack of knowledge of probabilities and consequences of spills. Methods to improve knowledge available to the public on gasoline spills and methods to improve estimates of environmental damages from gasoline spills is presented. Generalization of methodologies to hazardous materials in general are discussed.

Authors:
Eagen,P. D.

Keywords:
damage, environmental, Hazardous, highway, Highway Transportation, Gasoline, Interim, materials, methodology, methods, public, Risk, transportation, truck, trucks

Download Report:

Abstract:
The project goal was to evaluate different methods of cutting recessed skip stripe grooves, and to evaluate various pavement marking materials placed into the recesses. The project objective was to find a marking system for our mountain pass highways that would tolerate snowplowing and sanding operations, studded tires, and chain wear.Three methods of pavement grooving and three types of making material were evaluated over a four-year period. The grooving methods were evaluated with regard to production rate, the quality of the finished groove, and cost. The marking materials were checked for ease of installation, cost durability, and visibility.Only one method of grooving was found that produced the desired recess shape at a reasonable cost and in a timely manner. All three of the making materials were durable enough to survive for three years, but none produced the desired wet-daytime or wet-night visibility needed for adequate lane delineation. This loss of visibility under wet conditions was due to the lack of retroreflectance from the marking materials.

Authors:
Anderson,K. W.

Keywords:
chains, condition, cost, delineation, durability, grooves, grooving, highway, highway delineation, Highways, lane lines, materials, methods, night visibility, pavement, project, quality, rainfall, retroreflectance, snowplows, striping, studded tire, studded tires, System, tire, tires, Traffic markings

Download Report:

Abstract:
Trace organics were surveyed using gas chrornotography coupled to mass spectrometry for highway runoff samples from two Seattle sites . The characterization of the organics exhibited concentrations of aliphatic, aromatic and complex oxygenated compounds. Vehicles, including.exhaust emissions, were concluded to be the source of many of the organics.

Authors:
Zawlocki,K. R., Ferguson,J. F., Mar,B. W.

Keywords:
Concentrations, emissions, highway, highway runoff, Interim, Organics, runoff, seattle, survey, Washington, Water Pollutants, Washington State Monitoring

Download Report:

Abstract:
The project identified various highway roadways subjected to load restrictions for cataloguing on a District-wide map. An investigation of freeze-thaw events and pavement deflections was conducted in addition to collection of weather data at selected sites. "Frost Tubes" were evaluated and found to be an effectivetool for measuring frost depths. Limited data was collected due to warm winters and short freeze-thaw cycles. It was concluded that load restrictions are not needed until the temperature changes to a warming period. Additional research is needed to determine when load restrictions should be removed.

Authors:
Whalen,K.

Keywords:
data, Freeze Thaw, freeze-thaw, frost, Frost Tubes, Frozen Pavement, highway, load restrictions, pavement, pavement deflection, project, research, roadway, temperature, winter

Download Report:

Abstract:
Mass balances conducted on soils adjacent to highways indicated low mobility of metals deposited on well-vegetated surfaces. Grass drainage channels were shown to effectively capture and retain metals (e.g. a 60 m channel removed 80 percent of the original Pb concentration). Mud or paved channels, however, demonstrated little or no ability to remove metals from runoff. Metal release studies suggested that acid precipitation could release metals bound in the soil, especially where low buffering capacity exists.

Authors:
Wang,T. S., Spyridakis,D. E., Mar,B. W., Horner,R. R.

Keywords:
capture, deposition, drainage, embankment, Embankments, heavy metals, highway, Highways, impact, impacts, metals, mobility, overland flow, quality, runoff, soil, transport, Washington state, Water pollutants, water quality

Download Report:

Abstract:
An extensive literature review , laboratory column study and field observations indicated that leaching of soluble pollutants from woodwaste submerged in groundwater will be completed within a few years. Longer periods of leaching will be generated by woodfills above groundwater exposed to precipitation or infiltration of runoff. Expressions to model the quantity and characteristics quality of leachate from woodwaste fills used for road embankments were developed, and mitigating measures to reduce the impact of leachates are proposed.

Authors:
Vause,Kurt H., Ferguson,John F., Mar,B. W.

Keywords:
column studies, developed, embankment, Embankments, highway, impact, impacts, infiltration, Leachate, model, Pollutants, quality, review, runoff, water quality, Woodwaste fills

Download Report:

Abstract:
Transportation improvements of all kinds are being evaluated more carefully than ever during the planning stages. This attention to detail is well justified because the implications of such projects transcend the engineering disciplines and have environmental, social , and economic effects of major importance. In the economic area one of the impacts that is of great concern to the public i s the effect of a highway on property values. The purpose of this study is to measure the beneficial and adverse effects of limited- access highways on property values. A need exists in the State of Washington to have current data and analyses concerning this subject that apply specifically to this state . In addition there have been several theoretical developments that allow refinement of previous studies and validation of the results .OverviewThis study analyzed the beneficial effects of a highway on the values of surrounding properties by determining the real estate price trends in areas where a highway was constructed and comparing these trends with those in comparable areas which did not experience such changes. There were four residential areas utilized for parts of this study: Kingsgate east of Lake Washington on 1-405, north King County along 1-5 north of the Seattle city limits , Spokane near the east city limits along 1-90, and the southeast section of Puyallup along SR 512. Because of the lack of an adequate control area f o r the Spokane study, only the other three areas were used for the benefit estimation.

Authors:
Social and Econonomic Planning Section of the WA State Department of Highways

Keywords:
benefit, control, counties, data, development, environmental, highway, Highways, impact, impacts, improvement, planning, project, property values, public, seattle, transportation, Washington

Abstract:
The objective of this research was to examine the effects that construction of a major highway has on the value of surrounding properties, a topic which is of great public concern. Information was obtained on actual sales prices, as well as the characteristics of the properties. Four residential study areas were used, and as many as 4,785 sales were obtained in each area. The information on building and neighborhood characteristics was used to generate a quality-adjusted price index. This index for the years during which a highway was opened was compared with an index for an area which had been unaffected by highway change. The results show that when the highway significantly increased the accessibility of the residences, property values increased by 12 to 15 percent. Unfortunately, the houses closest to the highway had this increase partially offset by a .2 percent to 1.2 percent reduction for each 2k dBA increase in the highway noise level. Houses with highway noise were not found to take any longer to sell. In a commercial-industrial area, land values were found to increase 16.7 percent when a major highway was opened. Interviews were conducted in both residential and commercial areas.

Authors:
Palmquist,R. B.

Keywords:
construction, highway, impact, improvement, index, interviews, noise, property values, public, Real Property, Land Value, Property Value, Noise Pollution, Highways, Freeways, research, Washington

Download Report:

Abstract:
A composite sampling device was developed that can be installed at less than ten percent of the cost of automatic sampling systems currently used in Federal highway runoff studics. This dcvi ce was operated for one year, along-side an automatic sampler at the 1-5 side, to demonstrate that the two systems provide statistically identical storm composites.

Authors:
Clark,David L., Mar,B. W.

Keywords:
cost, developed, highway, highway runoff, Interim, runoff, sampling, System, systems, Water Pollutants, Washington State Monitoring

Download Report:

Abstract:
A total of 241 storm events were sampled at ten sites during the first full year of statewide monitoring of highway runoff. Analyses of these data indicates that more than half of the observed solids in this runoff is traced to sanding operations. The total solids loading at each side-was correlated with traffic during the storm. The ratio of other pollutants to solids was linear when there was sufficient traffic-generated pollutants to saturate the available solids.

Authors:
Asplund,Randy L., Ferguson,John F., Mar,B. W.

Keywords:
data, highway, highway runoff, models, monitoring, Pollutants, runoff, traffic, Washington, Washington state, Water Pollutants, Washington State Monitoring

Download Report:

Abstract:
The pavement structure of SR 12 between Montesano and Elma, Washington was evaluated for the proposed heavy loads associated with construction of the Satsop power plant. Information used in evaluating SR-12 resulted from two sources which included field studies conducted by the Washington State Department of Transportation and development of various material strength parameters by the University of Washington. These data were used to model the pavement structure as a layered elastic system. By use of this analysis procedure, the stresses, strains, and deflections were estimated for the expected range of loading conditions. The results indicate that the most probable amount of damage (fatigue and rutting) expected for the non-cement treated base structural sections is less that one to two percent of available pavement life for the "expected" loading condition. An increase in either or both the trailer wheel load and pavement temperature will act to produce greater losses in pavement life. It is estimated that the tensile stresses in the cement treated base may exceed the tensile strength of this material.

Authors:
Mahoney,J. P., Tsunetta,Jerrold Y., Terrel,Ronald L.

Keywords:
analysis, base, condition, construction, damage, data, development, fatigue, highway, loads, materials, model, pavement, Pavement Evaluation, Materials Characterization, Layered Elastic System, Failure Criteria, Heavy Loads, pavement life, pavement temperature, strains, strength, stresses, System, temperature, transportation, Washington, Washington state, wheel load

Download Report:

Abstract:
This report covers the initial 15 months of effort to review the literature, select a prototype site, compare the performance of several automatic sampling devices, and install a prototype sampling site on 1-5 north of Seattle .

Authors:
Horner,R. R., Burges,S. J., Ferguson,J. F., Mar,B. W., Welch,E. B.

Keywords:
highway, highway runoff, Interim, monitoring, performance, review, runoff, sampling, seattle, Water Pollutants, Washington State Monitoring

Download Report:

Abstract:
Criteria for selecting statewide monitoring sites for highway runoff were established t o provide representative combinations of climate, traffic highway, land use, geographic and topographic characteristics , Using thesecriteria , a minimum of six sites - were recommended for use to this research.

Authors:
Aye,Robert C.

Keywords:
criteria, highway, highway runoff, land use, land-use, monitoring, research, runoff, traffic, Water Pollutants, Washington State Monitoring

Download Report:

Abstract:
The Central Avalanche Hazard Forecasting project has been funded by the Washington State Highway Commission since July 1975 in order to test the feasibility and effectiveness of central avalanche forecasting for the Cascade Mountain Passes and adjacent territory . Historically, avalanche forecasting in the Cascade Mountains has been done locally on an area-by-area basis by Highway Department personnel and by Forest Rangers and professional ski patrolmen at individual ski areas. This project explored the possibilities of improving both mountain weather and related avalanche forecasts for use by WSDOT during winter operations in the mountain passes and, secondarily, explored the usefulness of anarea-wide forecasting service to other, cooperating agencies. The aim of this work has been to establish the technical and administrative framework for an operational, on-going mountain weather and avalanche forecasting service for Western Washington under the joint support of interested public agencies. This aim has been achieved in autumn 1978 by the operation of an avalanche forecasting office administered by the US Forest Service, housed by the National Weather Service, and supported by WSDT, with additional peripheral support from both the public and private sectors. Previous reports published by the project include: Interim Report, June 1976 (Report No. 23.2); Final Report, June 1977 (Report No. 23.3)Implementation Report, December 1978, which will be published in Spring 1979If you would like to obtain copies of any of these reports, contact WSDOT Public Transportation and Planning Division in Olympia (SCAN 234-61 49) or the Avalanche Research Office on SCAN 323-7180 or Write Avalanche Research,Department of Atmospheric Sciences AK-40, University of Washington, Seattle,Phil Taylor, Research Engineer, has done an outstanding job of developing much of this equipment and devising methods of operation. He is, unfortunately, no longer with the University. He will be working in Autumn 1978 with the US Forest Service as a consultant in addition to his continuing work with the US Geological Survey. This Operating Manual is intended to be an informational document with limited distribution and its format reflects that informality.

Authors:
University of Washington

Keywords:
agencies, avalanche, avalanche forecasting, developed, effectiveness, equipment, forecasting, framework, hazard, highway, Interim, ITS, manual, methods, Operating, planning, project, public, research, survey, transportation, Washington, Washington state, winter

Download Report:

Abstract:
Experiments were conducted at six locations to determine methods for eliminating or controlling existing weeds on highway rights-of-way prior to planting, and preventing weed infestations after planting, without injuring or interfering with normal growth and development of desirable plant material. Four experiments were conducted to determine herbicide programs for eliminating weeds in natural stands of (Arctostaphylos uva-ursi [L.] Sprang) and salal (Gaultheria shallon Pursh.) on highway rights-way, permitting these plants to form solid of uniform attractive vegetation.

Authors:
Ryan,George F., Rosenthal,Russell N., Berger,Robert L.

Keywords:
Chemical, control, development, highway, methods, program, Right-of-way, roadside, roadside vegetation, Roadside Vegitation, Weed Control

Download Report:

Abstract:
The Central Avalanche Hazard Forecasting project had had two principal aims : The design and establishment of an avalanche data network and central avalanche and mountain weather forecasting facility to serve the highway passes and other hazard areas of the Cascade Mountains in Washington. Improvements in the practices of conventional avalanche forecasting and the introduction of new techniques in statistical analysis and pattern recognition. Achievement of the first aim has been described in previous Reports 23.2 and 23.3. This present Report 23.4 gives the results of fundamental research into avalanche forecasting theory and discusses the application of these results is to central avalanche forecasting for the Cascade Mountains of Western Washington .

Authors:
LaChapplle,E. R., Furguson,S. A., Marriott,R. T., Moore,M. B., Reanier,F. W., Sackett,E. M., Taylor,P. L.

Keywords:
analysis, avalanche, avalanche forecasting, snow, weather, data, design, facilities, forecasting, hazard, highway, project, research, Washington

Download Report:

Abstract:
The Alternate Methods of Avalanche control project has been funded by the Washington State Highway Commission since August 1974 in order to develop simple, reliable and repeatable methods of triggering avalanche release which are free from the storage, handling and availability problems of explosives and artillery shells and which can be readily applied to avalanche paths typical to many smaller ones causing hazards for highways.The Alternate Methods of Avalanche Control project has been funded by the Washington State Highway Commission since August 1974 in order to develop simple, reliable and repeatable methods of triggering avalanche release which are free from the storage, and availability problems of explosives and artillery and which can readily be applied to avalanche paths typical of the many ones causing frequent hazards for highways. The research involved tests in both Washington and Colorado to permit evaluation of the control methods in diverse climates and snow conditions, leading to more generally applicable results than could be obtained at a single site. The technical and scientific aspects of the work in Colorado were coordinated by the San Juan Avalanche Project of the University of Colorado. Field work in Washington state and the general supervision of the program and the engineering design were carried out by the University of Washington Geophysics Program. The U.S. Forest Service at Utah, also joined in a cooperative test of our methods and equipment. This Final Report describes the tests and the results of the entire project.

Authors:
LaChapplle,E. R., Bell,D. B., Johnson,J. B., Lindsay,R. W., Sackett,E. M.

Keywords:
availability, avalanche, snow, weather, stress waves, condition, control, design, equipment, evaluation, hazard, highway, Highways, program, research, tests, Washington, Washington state

Download Report:

Abstract:
A series of measurements was undertaken in the summer and fall of 1977 to determine the noise radiated by a wide variety of cars and trucks, and the effect of an acoustic wall, or barrier, on suppressing the transmission of that noise. The assumption of the \"correct\" effective radiating height was found to be the most critical parameter in making the calculations agree with the measured results. The \"best height\" value varied greatly from vehicle to vehicle, and with speed, load, and throttle setting for a given vehicle. The variability of this parameter made it impossible (solely from these tests) to assess such considerations as whether Fresnel\'s or Maekawa\'s curves should be used to calculate the attenuation produced by the wall.The most noteworthy observation from this study is that newer trucks not only are quieter (to meet noise radiation standards) but have an effective radiating height as low as 2 ft compared to as much as 11 ft for older trucks. \'Thus, as the newer types of trucks become predominant in the highway traffic mix, the effectiveness of walls and barriers in shielding the community from noise will increase considerably.This is good news, because wall effectiveness has been marginal at best for pre-1970 trucks because of their radiation heights.

Authors:
Foss,R. N.

Keywords:
attenuation, barrier, barriers, effectiveness, Fresenel diffraction, highway, Highway acoustics, noise, noise screens, Noise supression, speed, tests, traffic, truck, trucks, vehicle noise, walls

Download Report:

Abstract:
Experimental data indicate that the combined effects of wind shear and ground plane attenuation can have a strong influence on sound propagation near the ground even at distances as short as 100 ft, The effectmanifests itself experimentally as a noticeable difference between sound propagation upwind vis-8-vis downwind that becomes more pronounced with either increased distance or increased wind speed. Differences of up to 25 dBA were found between into-the-wind and with-the-wind propagation fora listening height of 4 ft and a transmission distance of about 300 ft. Even a very moderate wind (4 mph) produced a difference of 12 dB at 150 ft for the same listening height. A large body of spectral data was also taken under a variety of wind conditions for path lengths of 150 ft and 225 ft. The resulting spectra agreed reasonably well with theoretical predictions for frequencies below 500 Hz, where ground and surface waves predominate; an important observation is that these waves were not affected substantially by wind conditions. Above approximately 500 Hz, the attenuation was frequently more than that predicted theoretically, and it was wind sensitive. The effect of wind was, in many cases, large, and could well mean that much experimentally obtained highway noise data is considerably less useful than previously thought, unless wind shear was taken into account during the measurements. In general, to "hear" the full effect of existing traffic, measurements should be made when the test positions downwind from the traffic.

Authors:
Foss,Rene N.

Keywords:
account, attenuation, condition, data, experimental, highway, Highway acoustics, ground plane attenuation, wind shear, interaction, noise, prediction, speed, traffic, wind

Download Report:

Abstract:
A photogrammetric monitoring method of structural deformation has been developed during the course of this project. The Gabion Wall which is part of the I-90 project has been used as the site for practical tests of the theorectical development. The monitoring consists of photographing the structure from three camera stations with KA-2 f=24" camera. The camera has been modified to a plate camera to provide the maxium accuracy.The methodology consists of the geodetic determination of the camera location and the orientation and photogrammetric determination of targets (natural and artificial) on the structure. During the course of this project more than 100 target locations were determined by three dimensional coordinates. the maximum error was found to be + 3/4 inch; the average, 1/2 inch. This represents a relative accuracy of from 1/58,00 to 1/120,00 of the photographic distance.Using the actual construction site for research has permitted immediate implementation. The instrumentation as well as the methodology along with the computer program has been transmitted to the Washington State Highway Department and their Photogrammetric Branch has been assisted in the implementation.

Authors:
Veress,S. A., Flint,E. E., Sun,L. L., Jinina,C.

Keywords:
camera, computer, computer program, construction, developed, development, Error, Gabion, highway, methodology, monitoring, Photogrammetry, Gabion Wall, deflection, camera stations, orientation matrices, space intersection space resection, program, project, research, tests, Washington, Washington state

Download Report:

Abstract:
This report reviews the second year of work on the Washington State Highway Commission Department of Highways project Central Avalanche Hazard Forecasting (WSDH Agreement Y-1700) to test the feasibility and effectiveness of central avalanche forecasting for the Cascade Mountain passes and adjacent area. The possibilities and techniques for improving both mountain weather and related avalanche forecasts for use by WSDH during winter operation in the mountain passes were further explored, and, secondarily, the usefulness of an area wide forecasting service to other cooperating agencies. This report defines and significant changes from the first year of operation in collection, assimilation or transmission of snow, weather and avalanche data by the Forecasting Office, and details modifications of the data network itself, especially new instrumentation and telemetry equipment . Weather and avalanche forecasting accuracy and reliability are assessed by comparing daily weather and avalanche forecasts with file d data. The conceptual framework and analytical methods used by forecasters to deduce current and probable future avalanche activity from the available data network input and current and extrapolated meteorological data are presented. A general preliminary guide to forecasting methodology for the Washington Cascades is defined and discussed.

Authors:
LaChapplle,E. R., Moore,M. B., Reanier,F. W., Sackett,E. M.

Keywords:
agencies, avalanche, avalanche forecasting, snow, weather, data, effectiveness, equipment, forecasting, framework, hazard, highway, Highways, methodology, methods, project, reliability, review, Washington, Washington state, winter

Download Report:

Abstract:
As part of their continuing effort to prolong the life of existing pavement systems, highway engineers must continue to improve upon design and rehabilitation methods. In past years, design methods based upon empericism have been employed with considerable success. As loading and materials change or become more complex, the older practices become less useful and a new approach undertaken. Throughout the U.S. and elsewhere, there has been emerging new technology often termed " rational " , "systematic", "mechanistic", and other terms used to describe new approaches to pavement analysis and design. Mostof these are based on elastic or viscoelastic layered representation of the pavement structure and have the potential to become powerful tools for the highway engineer. In recent years, the University of Washington has assisted the Washington State Highway Department on various research projects . One project resulted in a report that has been used to develop guidelines for allowable truck traffic through the concept of pavement damage and/or remaining life . The basis forth is report was the concept that pavement structures can be reasonably well represented by elastic layered systems. Analysis of the mechanistic behavior can then be used to predict pavement response and l i f e expectancy. As a result of this study and after discussions with Highway Department personnel, it was determined that the procedures, techniques, as well as other information used in the above report may be of further interest to them. In other words, the methods as well as results had potential utilization in a wide range of applications . As a result , a seminar program was set up whereby the writer would conduct or lead weekly discussion sessions on key topics.

Authors:
Terrel,R. L.

Keywords:
analysis, applications, behavior, damage, design, highway, materials, mechanistic, pavement, pavement damage, program, rehabilitation, remaining life, research, seminar, structures, systems, technology, traffic, truck, Washington, Washington state

Download Report:

Abstract:
A six year study of landscape plant establishment on roadsides as affected by a number of environmental conditions was initiated in April, 1970. The relationships between plant survival and soil texture, soil temperature, soil moisture, and exposure were evaluated. The affect of exposure on percent ground coverage of various grass species used in erosion control was also evaluated.

Authors:
Rosenthal,R. N.

Keywords:
condition, control, environmental, erosion, erosion control, exposure, highway, Landscape plant establishment, plant survival, roadside, soil, soil moisture, soil temperature, soil type, temperature

Download Report:

Abstract:
This report summarizes the first year of activity under Washington State Department of Highways project Central Avalanche Hazard Forecasting (Agreement Y-1700) to test the feasibility and effectiveness of central avalanche forecasting for the Cascade Mountain Passes and adjacent territory . This project explores thepossibilities of improving both mountain weather and related avalanche forecasts for use by the WSDH during winter operations in the mountain passes, and, secondarily, explores the usefulness of an area-wide forecasting service to other, cooperating agencies. The eventual aim of this work is to establish thetechnical and administrative framework for an operational, on-going mountain weather and avalanche forecasting service for Western Washington under the joint support of interested public agencies.

Authors:
LaChapplle,E. R., Moore,M. B., Reanier,F. W.

Keywords:
agencies, avalanche, avalanche forecasting, snow, weather, effectiveness, forecasting, framework, hazard, highway, highways, Interim, project, public, Washington, Washington state, winter

Download Report:

Abstract:
At the request of the Washington State Department of Highways a study was conducted to evaluate three computer models specifically designed to predict carbon monoxide concentration at receptor points along roadways. The models were evaluated on their ability to predict values obtained from a monitoring network established along various roadways in the State of Washington. Monitoring consisted of 12 ground level CO stations, meteorological stations and traffic counters. Traffic speeds were sampled for conformity during peak hours. The final selected models, CALINE and EPA's HIWAY were given calibration factors to be used when calculating Receptor Concentrations for Impact Assessments.

Authors:
Badgley,Franklin, Rossana,T. August, Alsid,Hal F., Lutrick,David

Keywords:
air pollution, air quality, Assessment, calibration, carbon monoxide, computer, Computer Modelin, Concentrations, highway, Highways, impact, model, models, monitoring, quality, roadway, speed, traffic, Transportation Pollution Source, Washington, Washington state

Download Report:

Abstract:
Part 2 continues the Cascade Passes Avalanche Atlas; Part 1 was published in August 1974 and covers avalanche hazards on Chinook, Cayuse, White and Snoqualmie Passes. The documentation of hazards at Stevens Pass includes only those avalanche paths which directly or potentially affect the highway, U.S. 2. There are numerous other adjacent avalanche paths--Lichtenberg Mountain is a good example--which are prominent in the vicinity of the Pass but which do not present any real likelihood of reaching the highway under foreseeable avalanche conditions. These latter paths are not delineated on the maps or photos, although many do appear within the mapped areas. There is a long history of avalanche occurrences at Stevens Pass, stemming both from railroad and highway experience. Most of the earlier history is unrecorded. A considerable amount of anecdotal knowl- edge for recent years is available from Highway Department personnel with long experience in the area. The historical record has drawn heavily on this experience. The primary compilation of data for Part 2 of the Cascade Passes Atlas was done by Len Miller during his tenure as a contract avalanche consultant for the Highway Department. This compilation has subsequently been amended and extended through the cooperation of the Department avalanche crew at Stevens Pass under the leadership of Steve Reister.

Authors:
LaChapplle,E. R., Brown,C. B., Evans,R. J.

Keywords:
Atlas, avalanche, Cascade, condition, data, hazard, highway

Download Report:

Abstract:
This research project was to evaluate the different variables in photogrammetric practice, which include targeting, film and development process, camera platform and achievable accuracy.Design criteria and standards have been established, which include the manufacturing of camera suspension for helicopter from both a theoretical and practical point of view. The testing of these standards and design criteria includes a large number of data. Thus, they have a high statistical probability of being correct. The project has proved that an all-time photography is possible with the proper selection of camera platform, and that the use of very low flight photography will enable the Highway Department to extend the use of photogrammetric measurement.

Authors:
Veress,S. A., Aramaki,A. A., Hall,J. K., Takamoto,T.

Keywords:
camera, criteria, data, design, design criteria, development, helicopter, camera suspension, target, shutter, vibration, accuracy, air speed, residual errors, highway, research

Download Report:

Abstract:
This research project was to evaluate the different variables in photogrammetric practice, which include targeting, film and development process, camera platform and achievable accuracy.Design criteria and standards have been established, which include the manufacturing of camera suspension for helicopter from both a theoretical and practical point of view. The testing of these standards and design criteria includes a large number of data. Thus, they have a high statistical probability of being correct. The project has proved that an all-time photography is possible with the proper selection of camera platform, and that the use of very low flight photography will enable the Highway Department to extend the use of photogrammetric measurement.

Authors:
Takamoto,T.

Keywords:
camera, criteria, data, design, design criteria, development, highway, Highways, research, Washington, Washington state

Download Report:

Abstract:
On July 14, 1970, an access hearing was held for that section of SR 405 which includes the Wilburton Interchange. This study has shown that there is good correlation between community perception, computer prediction and physical measurement of noise levels and attenuation.Community ResponsesAn opinion questionnaire was sent by the Highway Department in October, 1973 to all the people in the Woodrodge Community who might be affected by the completed noise barrier. Returned questionnaires are shown in Appendix A. Resulsts show that most people living directly behind the barrier have noticed some improvement in the noise level. Since 3 dBA change is barely preceptible by most people, this correlates well with measured attenuation, as the respondents indicating "no change" all resided in areas where less that 3 dBA attenuation was measured. See map #2.The barrier, however, had little effect on truck noise which was expected since low frequency noises are so difficult to attenuate. Low frequency noise waves go over and around most barriers. Dr. Van Ostrand who lives at the south end of the barrier (house number 1513) notices an increase in truck noise which would be similar to a truck coming out of a tunnel. Generally those living directly behind the barrier had evenly divided opinions in the categories of "More", "Same", or "Less" noise from trucks. Only one person indicated technical knowledge about noise and made any specific observation. He indicated noticeable overall improvement but with no change in "spike" noises. Almost everyone returning a questionnaire agreed that the barrier is aesthetically acceptable.

Authors:
Roberts,E. I.

Keywords:
Acousitc, attenuation, barrier, barriers, computer, hearing, highway, Interim, noise, Noise Levels, prediction, Report SR 405, truck, trucks, Wilburton Vicinity

Abstract:
A collection of reports about avalanche conditions and avalanche prevention measures on Washington mountain highways in general and to the North Cascade Highway in particular involving various aspects of creep deformation and glide of the snow cover as they affect avalanche defense structure design; reconnaissance of a proposed new highway route through the Cascade Mountains and a continuing study of the relationship between synoptic winter weather patterns and the formation and distribution of snow avalanches in the Cascades.The reports are entitled:1. Effect o f Glide and Creep on Rigid Obstacles by C.B. Brown and R.J. Evans.2. Creep and the Snow-Earth Interface Condition in the Seasonal AlpineSnow-Pack by D. M. McClung.3. In- Situ Investigations o f the Temperature Dependence o f the Creep ofLow Density Snow by D.M. McClung4. Naches Tunnel Avalanche Reconnaissance by E. R. LaChapelle.5. Investigation of Synoptic and Surface Weather Situations Leadinq toAvalanche Cycles in the Washinqton Cascades for the 1973-74 winter by M. B. Moore.

Authors:
Moore,M. B., McClung,D. L., LaChapplle,E. R., Brown,C., Evans,R. J., LaChapplle,E. R.

Keywords:
avalanche, Avalanche Forecasting, Avalanches, Cascade, condition, creep, density, design, glide, highway, Highways, North, North Cascade, seasonal, snow, Study, temperature, Washington, weather hazards, winter

Download Report:

Abstract:
This Summary Report synthesizes the work on avalanche control carried out at the University of Washington from 1970 through 1974. Five problem areas are addressed: 1. Identification of avalanche paths. 2. Description of historical frequency and size of avalanches. 3 Prediction of avalanche. 4. Identification of control methods. 5. Inclusion of control and prediction schemes in highway design and operation.

Authors:
LaChapplle,E. R., Brown,C. B., Evans,R. J.

Keywords:
avalanche, snow, decisions, weather, vegetation, creep, glide, avalanche forecasting, control, design, highway, highway design, methods, prediction, Washington

Download Report:

Abstract:
This present compilation of avalanche paths affecting Washington State highways extends in the same format the information published in 1971 as the North Cascades Highway Avalanche Atlas. Part 11, in preparation, will cover Stevens Pass and Tumwater Canyon.The North Cascades Highway Atlas was prepared on the basis of extensive aerial and ground reconnaissance in a hitherto inaccessible wilderness area where no previous record of avalanche occurrence was available. Compilation for the Cascades Passes has proceeded on the same basis, with the added advantage that all of the areas in question have long been traversed by highways for which considerable historical records exist . It is necessary, though, to note that such a record has proven to be less advantageous than might be expected. In the case of the North Cascades Highway, identification of avalanche paths was based on objective appraisal of terrain and vegetation patterns, leading to an accurate and highly consistent compilation. In the present Cascade Passes Atlas, there are many instances where objective evidence and historical accounts fail to agree. Moreover, the nomenclature, rather than being assigned consistently, has developed -- ad hoc over the years and varies with individuals and agencies . These conflicts have been resolved in the final editing of this Atlas according to the best available evidence, but in some cases necessarily in an arbitrary fashion. The Snoqualmie Pass section of this Atlas includes reproductions of sketches prepared by the Department of Highways for use in recording avalanche occurrences. These sketches are included here to illustrate this mode of avalanche recording, since it is a valuable method for systematically accumulating an historical record of avalanche frequency and behavior.

Authors:
LaChapplle,E. R., Brown,C. B., Evans,R. J.

Keywords:
account, agencies, Atlas, avalanche, behavior, Cascade, developed, highway, Highways, North, North Cascade, Washington, Washington state

Download Report:

Abstract:
This study was chiefly aimed at determining if a standard precast concrete median barrier placed on a highway shoulder in a fill section, would be effective in reducing highway traffic noise outside of the roadway prism. Secondly, it attacked the question of whether the current computer noise prediction program was giving accurate values.The first phase of the study consisted of collecting noise and traffic measurements in the field, first without and then with a median barrier, at two selected test sites. Next, the geometry of the test sites and field traffic data were entered into the computer program and the predicted noise levels obtained.The second phase consisted of comparing these two sets of data to determine the accuracy of the computer program and the amount of sound reduction, if any, due to the median barrier.The results indicated that the highway traffic noise was dominated by truck generated noise. It was therefore concluded that a standard median barrier will not provide a significant amount of sound reduction, outside of the roadway prism, when placed on a highway shoulder in a fill section. The results also indicated that the current computer noise prediction program will calculate noise levels that are usually higher than actually exist.

Authors:
Klasell,J. A., Butler,B. W.

Keywords:
Acoustical barrier, barrier attenuation, computer, computer program, concrete, data, ground attenuation, highway, median, median barrier, noise, Noise Levels, precast, precast concrete, prediction, program, research, roadway, traffic, traffic data, traffic noise, truck, wind, wind noise, barrier, project

Abstract:
This study was conducted to collect data on the operational characteristics of highway, snow, and studded snow tires and other winter traction aids. The objective of the study was to perform various vehicle maneuvers to evaluate the tire characteristics on wet and dry pavement surfaces. Tests took place on the Washington State Patrol Driver Training Course at Sanderson Field, located west of Shelton, Washington. The testing was done with the cooperation of the Washington State Patrol who furnished personnel and equipment to assist in this research effort.This test maneuvers evaluated during the study are as follows:Test No. 1 Maneuvering (Serpentine Course)Test No. 2 Hairpin CurveTest No. 3 High Speed Lane ChangeTest No. 4 Locked-Wheel StopIn addition to the three types described above, other new traction type products and tires were evaluated. These consisted of studded snow tires with "Norfin" studs, and Garnet impregnated snow tires. Studded tires on all four wheels were also evaluated, at the request of the Washington State Patrol. This combination is used by Troopers assigned to mountain highway passes and areas where there is a large buildup of snow and ice during the winter. This report consists of two areas of evaluation. One involves tire combinations (front and rear) and the other is the evaluation of individual tire types. In addition to these two areas, a separate section is devoted to the tire and vehicle characteristics of Washington State Patrol's vehicle when compared with a Department of Highway's Motor Pool Vehicle. Included also is the test vehicles' description.

Authors:
Toney,Carl A.

Keywords:
data, equipment, evaluation, highway, No Keywords found in report, pavement, pavement surface, research, snow, speed, studded tire, studded tires, studs, tests, tire, tires, traction, training, Washington, Washington state, winter

Download Report:

Abstract:
Federal and State laws require highway departments to prepare statements assessing the impact that proposed highway improvements or construction may have on the environment. An important consideration in the preparation of an impact statement is the anticipated effect the proposed activity will have on air quality since highway transportation is a source of several major air pollutants: particulate matter, nitrogen oxides, carbon monoxide, hydrocarbons, and photochemical oxidants which are formed in the atmosphere in the presence of sunlight. Comprehensive physical studies to predict the air quality impact at proposed sites are generally prohibitive due to the time required to obtain suitable data, the cost of such studies and the number of impact statements that must be considered by most highway departments.Methods have been developed to predict the air quality impact of new highway construction through the use of mathematical atmospheric diffusion models. Once they are properly calibrated these models can be used to test alternative locations and designs. Basically models use meteorological conditions and emission rates to predict downwind concentrations as illustrated in Figure 1.The principal objective of this research project has been to conduct a search of the literature to identify state-of-the-art air quality predictive schemes applicable to motor vehicle transportation. The available models have been analyzed in detail and evaluated in terms of selected characteristics that serve to describe the predictive capabilities of each. Limitations in the models have also been noted where appropriate.Section 2.0 o f this report describes the methods used in conducting the research. Sections 3.0 and 4.0 present the models analyzed and a general discussion of applicability, in both narrative and tabular form. Section 5.0 summarizes the study and presents the recommendations for future consideration.

Authors:
Rossano,A. T., Lamb,Donna V., Badgley,Franklin

Keywords:
air quality, Alternative, carbon monoxide, Concentrations, condition, construction, cost, data, design, environment, highway, highway construction, Highways, hydrocarbons, impact, model, modeling, models, nitrogen, particulate matter, Pollutants, quality, research, state-of-the-art, transportation, Washington, Washington state

Download Report:

Abstract:
A four year study of landscape plant establishment as affected by a number of environmental conditions was initiated in April, 1970. The relationship between plant survival and soil texture, soil temperature and exposure were evaluated. The affect of exposure on percent ground coverage of various grass species used in erosion control was also evaluated.

Authors:
Rosenthal,Russell N.

Keywords:
condition, control, environmental, erosion, erosion control, exposure, highway, Landscape plant establishment, plant survival, soil, soil temperature, soil type, temperature

Abstract:
Semi-analytical, analytical, and analogical aerotriangulation methods, procedures, instructions, and recommendations are explained in detail.Acceptable accuracies, required technical operator skill, operational time requirements, and instructions for adoption of semi-analytical aerotriangulation into the Photogrammetric Department are shown. Computer programs for space resection, linear transformation, and model connection procedures are included.

Authors:
Hou,Cheng-Yeh

Keywords:
Aerotriangulation, computer, computer program, highway, Highways, model, program, Semi-analytical, analytical, analogical, linear transformation, lens distortion, film distortion, space resection, level method

Download Report:

Abstract:
The objective of this study was to present criteria and procedures for evaluation of Joint Development (JD) above, below, or beside s t a t e highways. Application of the procedures a re-illustrated over a wide range of joint development situations, both (1) for establishing state or local J D policy, and (2) for making decisions about JD projects in a more timely and comprehensive manner, and in a way that will contribute toward improving the quality or urban life or the enhancement of rural environments. The approach taken in the Guidelines is sequential, systematic, and interdisciplinary; that is, it uses a series of successively more detailed and comprehensive planning and evaluation procedures for JD decision-making, relying on a wide range of specified physical, economic, social, and legal criteria. In use, the Guidelines envision a three- stage planning and evaluation process:(1) identification of the need or potential for J D projects, (2) comparison of project proposals against policies, criteria and standards designed t o avoid or minimize negative impacts and increase favorable impacts; and (3) refined definition of costs and benefits when warranted.

Authors:
Van Zandt,E. Jack

Keywords:
benefit, benefits, cost, costs, criteria, development, Enviromental impact, environment, evaluation, highway, Highway planning, Highways, impact, impacts, joint development, Multiple use, planning, policy, quality, rural, urban

Download Report:

Abstract:
The objective of this study was to present criteria and procedures for evaluation of Joint Development (JD) above, below, or beside state highways. Application of the procedures are illustrated over a wide range of joint development situations, both (1) for establishing state or local JD policy, and (2) for making decisions about JD projects in a more timely and comprehensive manner, and in a way that will contribute toward iwro;ing the quality of urban life or the enhancement of rural environments. The approach taken in the Guidelines is sequential, systematic, and interdisciplinary; that is, it uses a series of successively more detailed and comprehensive planning and evaluation procedures for JD decision making relying on a wide range of specified physical, economic, social and legal criteria. In use, the Guidelines envision a three-stage planning and evaluation process:(1) identification of the need or potential for JD projects; (2) comparison of project proposals against policies, criteria, and standards designed to avoid or minimize negative impacts and increase favorable impacts; and (3) refined definition of costs and benefits when warranted. This supplement to the Guidelines report (described above) presents the results of analyzing seven actual JD proposals, located along Interstate 5 in the State of Washington, according to the procedures suggested in the Guidelines,

Authors:
Van Zandt,E. Jack

Keywords:
benefit, benefits, cost, costs, criteria, development, environment, evaluation, highway, Highways, impact, impacts, joint development, Joint Development, Multiple Use, Highway Planning, Enviromental Impact, planning, policy, quality, research, rural, transportation, urban, Washington

Download Report:

Abstract:
In many parts of the world, the design of flexible pavement is still based on empirical methods which have developed from engineering experience. These empirical methods cannot be extrapolated beyond their limits without full scale trials to prove their applicability. In recent years, however, the increase of traffic, both in volume and axle loads, has led to the failure of many roads previously considered well designed. For this reason, therefore, researchers realized that a closer look at the pavement materials was desirable in order to develop a rational design procedure. Due to the complexity of characterizing pavement materials, and the limitations of instrumentation, much of the reported work offered little help in changing design practice. This is, perhaps, due to many simplifying assumptions which had to be introduced in the experimental procedure as well as the interpretation of the test results. Recently, however, there has been a sharp advancement in test instrumentation and an outstanding progress in processing the experimental results. This has been reflected through many fine investigations and has increased the demand for more improvements. An asphalt pavement is a complex structure whose function is to provide a suitable surface for a highway, an airport, or other off-highway facility. The load of a vehicle or an aircraft is transmitted through the multilayered system of processed materials which have different mechanical properties. The stress distribution within this system is highly complex and to a large extent is dependent on the relative stiffnesses of the individual layers.

Authors:
Terrel,Ronald L., Awad,S.

Keywords:
asphalt, asphalt pavement, axle, base, behavior, demand, design, developed, experimental, facilities, fine, highway, improvement, loads, materials, methods, pavement, stiffness, stresses, System, traffic, volume

Download Report:

Abstract:
A study was conducted on the character and significance of highway runoff waters for the Washington Department of Highways and the Federal Highway Administration. This preliminary appraisal of runoff quality consisted of a literature review and critique plus a limited amount of field sampling on SR 520. Although a large amount of information is present in the literature concerning urban run off, there is very little strictly related to highways and their rights-of- way. Highway runoff is similar t o urban area runoff but may be higher in heavy metals and oil. A significant fraction of the heavy m e t an l s, oil and nutrients are adsorbed to the dust and dirt fractions and then may be removed by sedimentation. Runoff from the lake bridges should have a very insignificant effect on Lake Washington in comparison with the urban run off to the Lake. Recommendations are made for mitigating runoff effects and for conducting an intensive study of highway run off water quality and its significance.

Authors:
Sylvester,Robert O., DeWalle,Foppe B.

Keywords:
bridge, bridges, environment, heavy metals, highway, highway runoff, Highways, ITS, metals, quality, review, runoff, sampling, sedimentation, Study, urban, vehicle emissions, Washington, water quality

Download Report:

Abstract:
A study was conducted of rest area wastewater disposal problems and related factors for the Washington State Highway Commission during the period of June - December 1971. This report on the study is intended to present an evaluation of present rest area wastewater systems together with feasibility analyses of alternative methods of waste handling. It is not intended to be a preliminary engineering design report.Data are presented on rest area problems as reported to or observed by the writers on field visitations. This is followed by discussions of criteria and standards presently used in rest area design together with data on water usage for those rest areas where "complete" data were available. Laboratory analyses were made on rest area wastewaters and on a certain additive, " Bacterial Waste Disposer", that has been used in some of the rest areas. A discussion is included on possible future trends and uses of rest areas and the need to minimize water usage. Chapter XI1 contains the principal thrust of the report in its discussion of possible rest area wastewater disposal methods with an evaluation and some relative cost data. With increasingly stringent requirements for wastewater disposal, it seems apparent that rest area wastewaters must continue to be disposed of on highway property. If not, the Department would find itself, in most instances, with the task of operating continuously and effectually some rather complicated treatment systems that require trained operators, operational reports and effluent analyses, and systems that are not usually amenable to the flow characteristics of rest area wastewaters. Since much national attention is being given to these problems, it is hoped that new or improved treatment schemes may be developed in the future that will be appropriate for rest areas. An intent of this study has thus been to suggest means of wastewater disposal, presently available that would offer an improvement to the septic tank drain field method of disposal.Conclusions and recommendations drawn from the study are as follows:1. There is no question but that septic tank- drain field disposal systems would, because of their simplicity, be the preferred method of disposal if their installation were applicable to most rest areas and if they would, from past experiences here and elsewhere give some assurance of a freedom from operating difficulties over a period of just a few years.

Authors:
Seabloom,Robert W.

Keywords:
additive, Alternative, cost, criteria, data, design, developed, disposal, evaluation, flow, highway, improvement, ITS, methods, Operating, rest area, rest areas, Study, System, systems, Washington, Washington state

Download Report:

Abstract:
At the request of the Washington Department of Highways a comprehensive study was conducted of the exposures of toll collectors to carbon monoxide at the Evergreen Point Bridge spanning Lake Washington between Seattle and Bellevue.The first phase of the study consisted of designing, installing and operating an automatic, continuous carbon monoxide monitoring system to establish typical air quality patterns in and around the toll booths.the second phase consisted of developing a prototype toll booth positive ventilation system. Air, which is introduced through a vertical diffuser situated at one wall of the booth, travels horizontally across the booth and out the door. Parametric studies of sources and rates of ventilation air, diffuser design and other toll booth modifications were conducted in the laboratory. Subsequently these modifications were installed and investigated at an operating booth at the toll plaza. Concentrations of carbon monoxide in the collectors breathing zone were reduced to acceptable levels. Methodologies and results of these systems are described, and design recommendations for the control system are offered.

Authors:
Rossana,T. A., Hall,F. A.

Keywords:
air quality, bridge, carbon monoxide, Concentrations, control, design, exposure, highway, Highways, methodology, monitoring, Operating, quality, seattle, System, systems, travel, Washington

Download Report:

Abstract:
An interim report of the second year of a three-year study of avalanche hazards along Washington mountain highways is presented. Applicable snow, avalanche and weather data for 1971-72 are given. Also included is a theoretical treatment o f the stress analysis of slab avalanches and a bibliography of snow clearing technology.

Authors:
LaChapplle,E. R., Brown,C. B., Evans,R. J.

Keywords:
analysis, Annual, avalanche, Avalanche control, Washington mountain highways, Snow and weather data, Snow clearing technology, Avalanches, control, data, hazard, highway, Highways, Interim, methods, snow, stresses, Study, technology, Washington, Washington state

Download Report:

Abstract:
This study was made to obtain information on the noise levels being emitted by vehicles currently using the highways of the State of Washington. The Washington State Highway Commission requested this study for guidance in proposing vehicle noise control legislation. The main controversy in states with existing comprehensive vehicle noise legislation has concerned trucks traveling on roads with posted speeds above 35 mph. The main thrust of our study is therefore concerned with this particular area, although data were also taken on automobiles and on roads posted at less than 35 mph. This study is unique in that the noise level - and the speed of all vehicles were measured. In addition, all trucks over 10,000 lb were weighed. Our large body of data has been graphed in numerous ways to illustrate various aspects--including how the noise factor varies with speed, weight, and percentage of full load, etc. Some photographs of the trucks together with their noise data a real so included.

Authors:
Foss,Rene N.

Keywords:
control, data, highway, Highways, noise, Noise Levels, speed, Study, truck, trucks, vehicle noise, Washington, Washington state, weight

Download Report:

Abstract:
The purpose of this study was to investigate the acoustic effects of two topping materials used on bridges in the Seattle area. One material was applied to the bridge on Interstate-5 which crosses the Duwamish River. It is an English product called Sprag-Grip which is supposed to have very good anti-skid properties, as well as the ability to stick to the road in thin layers thus making it suitable for the repair of worn surfaces. The other material is an epoxy -asphalt mixture which was applied to some sections of the Evergreen Point Floating Bridge over Lake Washington, particularly over sections where worn grating was causing excessive noise. Hopefully, this substance will be capable of long-term sticking in relatively thin layers. Of the two materials, it was found that the epoxy-asphalt topping on the Evergreen Point Floating Bridge was by far the quieter, and, at least as newly applied, proved to be very quiet at the road/tire interface. It is likely that this good acoustic performance is due to the smoothness of the surface rather than directly to the fact that the material contains epoxy. The role of the epoxy would be as an adhesive and to resist wear so that its original acoustic performance could be maintained for a considerable length of time. Spray-Grip, on the other hand, although slightly quieter than the rutted, worn roadway, was not as quiet as the original unworn road surface. Experimental Procedures The primary contribution of a road surface to the noise 'radiating from a vehicle is in the noise emitted at the road/tire interface; therefore, the major thrust of this effort was directed toward measuring this effect. There also were some measurements of community noise levels before and after the resurfacing of the bridges. The tire noise tests were taken on the right rear wheel of a Laboratory station wagon upon which a new tire was mounted (a Pennsylvania Patrol Special, size 8. 55-15). (The tread design and depth of this tire are shown on page 2. ) This tire was mounted on a wheel and used on the vehicle only daring tests. Between tests it was stored so that unnecessary wear would not change its acoustic character-teristics. The noise pickup device was a specially baffled microphone located about 7 inches from the road/tire interface by a bracket holding it on the outside of the tire. One of the major problems in making noise measurements of this type is to have a microphone that will pick up only tire noise and be baffled from wind noise. This problem has been solved by a microphone baffling system especially designed by this Laboratory.

Authors:
Foss,Rene N.

Keywords:
asphalt, bridge, bridges, community noise, design, Epoxy, experimental, floating bridge, highway, ITS, materials, mixture, noise, Noise Levels, noise measurements, performance, repair, roadway, seattle, Study, System, tests, tire, tire noise, Washington, wind, Wind Noise

Download Report:

Abstract:
This report covers activities for the eighteen months ending September 1971 under a Washington State Highway Department Contract for Research Project No. Y1301 with the University of Washington. Snow and avalanche climate varies widely across the parts of the Cascade Mountains spanned by SR-20. Little information is presently available about temperatures and weather patterns over the passes, but a limited amount of snow depth data are available from snow courses. These snow data are presented and analyed.

Authors:
LaChapplle,E. R.

Keywords:
avalanche, Avalanches, data, highway, Highway SR 520, North Cascade, project, research, snow, temperature, Washington, Washington state

Download Report:

Abstract:
This Avalanche Atlas catalogs details of snow avalanche activity along the North Cascades Highway, SR-20, between Newhalem on the west side of the Cascade Mountains and Mazama on the east side. Data contained herein have been collected during summer and winter reconnaissances in 1970 and 1971 under contract between the Washington State Highway Department and the University of Washington. Compilation of this Atlas completes the first phase of a planned three-year study of avalanche problems and control methods on the highways of the State of Washington.

Authors:
LaChapplle,E. R.

Keywords:
Atlas, avalanche, Cascade, control, data, highway, Highways, methods, North, North Cascade, snow, SR 20, Study, Washington, Washington state, winter

Download Report:

Abstract:
The Impulse Index as a measure of pavement condition was previously described in a report of the Research Division of Washington State University entitled, "Pavement Deflection Measurement - Dynamic-A Feasibility Study, Final Report, June 1970," by Frank W. Brands, P. E. and John C. Cook, P. E.Implementation of automatic data acquisition using impulse testing requires the development of a mechanical device to set an instrument package on the pavement, deliver an impulse of energy, and retrieve the instrument package. This is to be done automatically with the vehicle proceeding down the highway. This report describes a test model built to facilitate the determination of data necessary for design of a prototype vehicle.

Authors:
Brands,F., Cook,C. J.

Keywords:
condition, data, design, development, Energy, highway, impulse index, index, model, pavement, pavement deflection, research, Washington, Washington state

Download Report:

Abstract:
At the request of the Washington Department of Highways two studies have been conducted by a team of specialists at the University of Washington Air Resources Program to determine the applicability of the Acoustic Radar to air quality modeling to mobile sources.At the request of the Washington Department of Highways two studies have been conducted by a team of specialists at the University of Washington Air Resources Program to determine the applicability of the Acoustic Radar to air quality modeling of mobile sources. Following an exploratory investigation, a comprehensive study was undertaken in which the atmospheric structure was measured by a modified Monostatic Acoustic Radar and the derived stability conditions were compared with the commonly used Pasquill-Turner stability classes, which are based on empirical data. This comprehensive study was performed over a three month period in the fall of 1976, when an unusually persistent air stagnation existed in the study area caused by a stationary high pressure system over the entire Northwest.The Evergreen Point Floating Bridge Toll Plaza in Bellevue, Washington was selected for test location.The carbon monoxide (CO) concentrations were measured at six strategically located sampling points and then compared with the computer model predictions utilizing atmospheric stability data derived by both the Pasquill-Turner and the Radar echo methods. The results indicated that the Acoustic Radar method of determining D & E stability classes is a more realistic approach than that of the Pasquill-Turner Method. Furthermore, the Radar method can also provide continuous remote sensing and recordings of atmospheric parameters. The variation of the inversion height, as measured by the Radar echoes has shown a reasonably good correlation with the variation of the measured CO concentration.

Authors:
Rossano,A. T., Badgley,F. I., Juhasz,P. C., Bang,G., Carsey,F.

Keywords:
Acoustic Radar, air pollution, air quality, Air Quality Modeling, bridge, carbon monoxide, Carbon Monoxide Perdictions, computer, Concentrations, condition, data, floating bridge, highway, Highways, ITS, model, modeling, prediction, pressure, program, quality, remote sensing, Remote Sensing Atmospheric Structur, sampling, stability, Transportation Pollutio, Washington

Download Report: