UW WSU WSDOT

TRAC Reports


To sort the reports, click on a heading: Authors, Report #, Report Title, Year, or Publisher.
To download a report's pdf or see the abstract, click on the report.


Search returned 44 reports containing keyword: 'project'
clear results
Previous
Search
Next

Authors
Report #
Report Title
Year
Publisher
McCormack,E. D. WA-RD 607.1 Options for Benchmarking Performance Improvements Achieved from Construction of Freight Mobility Projects 2005 TRAC/UW
Abstract:
This report documents the development of data collection methodologies that can be used to cost effectively measure truck movements along specific roadway corridors selected by transportation agencies in Washington State. The intent of this study was to design and test methodologies that could be used to measure the performance of freight mobility roadway improvement projects against benchmarks, or selected standards, that would be used both as part of the project selection process and to report on speed and volume improvements that resulted from completed freight mobility projects. One technology tested was Commercial Vehicle Information System and Networks (CVISN) electronic truck transponders, which are mounted on the windshields of approximately 20,000 trucks in Washington. By using software to link the transponder reads from sites anywhere in the state, the transponder-equipped trucks could become a travel-time probe fleet. The second technology tested involved global positioning systems (GPS) placed in volunteer trucks to collect specific truck movement data at 5-second intervals. With GPS data it was possible to understand when and where the monitored trucks experienced congestion and to generate useful performance statistics. The study found that both data collection technologies could be useful; however, the key to both technologies is whether enough instrumented vehicles pass over the roadways for which data are required. This basic condition affects whether the technologies will be effective at collecting the data required for any given benchmark project. The report also recommends the traffic data that should be collected for a benchmark program and the potential costs of using either data collection technology.

Authors:
McCormack,E. D., Hallenbeck,M. E.

Keywords:
agencies, commercial vehicle, condition, congestion, construction, corridors, cost, costs, data, data collection, design, development, freight, freight mobility, freight movement reliability, global positioning, global positioning systems, GPS, improvement, methodology, mobility, networks, performance, positioning, probe program, project, research, roadway, software, speed, statistics, Study, System, systems, technology, traffic, traffic data, transportation, travel time, truck, truck monitoring, trucks, volume, Washington, Washington state


Download Report:
External Links:
http://www.wsdot.wa.gov/research/reports/fullreports/607.1.pdf http://wsdot.wa.gov/Research/Reports/600/607.1.htm
Kopf,J. WA-RD 619.1 Measurement of Recurring and Non-Recurring Congestion: Phase 2 2005 TRAC/UW
Abstract:
In 2003, the Washington State Department of Transportation (WSDOT) initiated a research effort to develop and test a methodology for estimating congestion delay on Seattle area freeways. The initial phase of the research developed a preliminary methodology for both measuring congestion and assigning that congestion to specific lane blocking incidents. In Phase 2 of this study, that methodology was automated and extended to include an examination of the effects of incidents occurring on the shoulders of the freeway, spillback from incident-caused congestion on one freeway that affects a second freeway that feeds traffic onto the initially congested facility, special events, and weather. Because funding for this effort was extremely limited, only three corridors (with both directions analyzed independently) and two months of data were analyzed. The project found that the Phase 1 methodology works well in assigning traffic congestion that occurs in the immediate time frame and geographic location of incidents to those incidents. It also showed that this process can be automated, making the data preparation effort now the primary determinant of the cost of additional work of this kind. Unfortunately, even with the addition of shoulder incidents, special events, and weather to lane blocking events, the automated process is unable to assign a significant proportion of the non-recurring delay occurring on Seattle freeways. The detailed analysis of freeway performance showed that much of the delay caused by specific incidents occurs in places or at times removed from the incident itself. The result is that much of the observed non-recurring delay can not be assigned to specific causes by the current analytical process. New analytical procedures will need to be developed in Phase 3 of this work. The Phase 2 analysis also confirmed that the congestion effects of specific incidents and other traffic disruptions are highly dependent on the background traffic conditions at the time of the disruption. While the Phase 2 analysis did not produce all of the results desired, the additional analyses showed that the summary statistics output from the Phase 2 software are useful as input to other analytical procedures.

Authors:
Kopf,J., Nee,J., Ishimaru,J. M., Hallenbeck,M. E.

Keywords:
congestion causes, freeway performance, traffic congestion, Washington, Washington state, transportation, WSDOT, research, methodology, congestion, seattle, freeway, developed, incident, Study, effects, traffic, facilities, corridors, data, project, cost, analysis, performance, in-place, condition, statistics, software


Download Report:
External Links:
http://www.wsdot.wa.gov/research/reports/fullreports/619.1.pdf http://wsdot.wa.gov/Research/Reports/600/619.1.htm
Al-Yagout, M.A. WA-RD 600.1 Improving Traffic Characterization to Enhance Pavement Design and Performance: Load Spectra Development 2005 TRAC/UW
Abstract:
This research addresses the understanding of, and need for, load spectra in future pavement design procedures and as a stepping stone toward more complete pavement design. The primary objective of this project was to develop truck axle load spectra for Washington State. To do this, axle load data collected at WIM stations throughout Washington State were used. The developed load spectra encompass the principal truck axles on the roadway network: single, tandem, and tridem. Achieving this objective allows the Washington State Department of Transportation, or any state highway agency with analogous traffic patterns, to accommodate the requirements of the 2002 Design Guide, developed through NCHRP Project 1-37A. A secondary objective of this project was to determine whether ESALs obtained from the developed load spectra are significantly different from historical values. Because the developed load spectra are transformable to ESALs, state highway agencies that decide not to use the new guide can still choose to employ the ESALs produced with the load spectra. The project concluded that the developed load spectra are reasonable. For single axles they are comparable to the 2002 Design Guide and MnROAD defaults. For tandem and tridem axles, they are slightly more conservative than defaults of the 2002 Design Guide and MnROAD, but they are still within reason. In addition, the ESALs per vehicle class associated with the developed load spectra are comparable to Washington State historical ESALs for vehicle classes 9, 10, and 13. The use of the newly developed ESALs per vehicle will generally increase design ESALs, but that increase will be due to inclusion of the less predominant vehicle classes (4, 6, 7, 8, and 11).

Authors:
Al-Yagout, M.A., Mahoney, J. P., Pierce, L., Hallenbeck, M.E.

Keywords:
Agencies, axle, data, design, developed, development, equivalent single axel load, ESAL, highway, load spectra, pavement, pavement design, performance, project, research, roadway, single axle, traffic, transportation, truck, Washington, Washington state, weigh-in-motion, WIM


Download Report:
External Links:
http://www.wsdot.wa.gov/research/reports/fullreports/600.1.pdf http://wsdot.wa.gov/Research/Reports/600/600.1.htm
Kristof,T. WA-RD 597.1 Assessing the Benefits of Traveler and Transportation Information Systems 2004 TRAC/UW
Abstract:
The goal of advanced traveler information systems (ATIS) is to provide travelers with information that will facilitate their decisions concerning route choice, departure time, trip delay or elimination, and mode of transportation. The benefits of ATIS projects can be evaluated through field studies, simulation software, and surveys. An evaluation method called the ITS Deployment Analysis System (IDAS) is suggested for use by the Washington State Department of Transportation (WSDOT). IDAS is a "sketch" planning tool intended for screening and prioritizing all intelligent transportation systems (ITS) projects (not just ATIS projects). The software evaluates a number of benefits. These are determined by changes attributable to the deployment of ITS in vehicle miles traveled (VMT), vehicle hours traveled (VHT), volume-capacity (v/c) ratios, and vehicle speeds throughout a given network. The IDAS evaluation depends on a number of assumptions that affect the calculations of costs and benefits. The IDAS developers recommend that these assumptions be inspected by local agencies and adjusted to better represent local conditions. The assumptions about the impacts on VMT, VHT, v/c ratios, and vehicle speed are particularly important. Consequently, suggestions are made within this report for adjustments that WSDOT should make to these default values. These values will allow the WSDOT to successfully employ IDAS for ATIS evaluation.

Authors:
Kristof,T., Lowry,M., Rutherford,G. S.

Keywords:
advanced traveler information systems, agencies, analysis, Assessing, ATIS, ATIS benefits, ATIS evaluation, benefit, benefits, condition, cost, costs, Deployment, evaluation, IDAS, impact, impacts, information systems, Intelligent transportation system, intelligent transportation systems, ITS, ITS Deployment Analysis System, planning, prioritizing, project, research, software, speed, Study, survey, Surveys, System, systems, transportation, traveler information, Washington, Washington state, WSDOT


Download Report:
External Links:
http://www.wsdot.wa.gov/research/reports/fullreports/597.1.pdf http://wsdot.wa.gov/Research/Reports/500/597.1.htm
Germaine,S. S. WA-RD 585.1 Screening Model for Determining Likelihood of Site Occupancy by Oregon Spotted Frogs (Rana pretisoa) in Washington State... 2004
Abstract:
The Oregon Spotted Frog is currently a federal Candidate for listing under the Endangered Species Act. The report provides a habitat screening that biologists in Washington State can apply in the field to determine whether wetlands contain suitable habitat for the Oregon Spotted Frog. In the event that this species is listed, the application of the model will facilitate a more streamlined consultation process of transportation projects in the event of this species.

Authors:
Germaine,S. S., Consentino,B. L.

Keywords:
amphibians, Endangered species act, frogs, habitat, model, occupancy, Oregon Spotted Frog, Pacific Northwest, project, Rana pretisoa, transportation, Washington, Washington state, wetlands, wildlife


Download Report:
External Links:
http://www.wsdot.wa.gov/research/reports/fullreports/585.1.pdf http://wsdot.wa.gov/Research/Reports/500/585.1.htm
Pierce,L. WA-RD 576.1 Dowel Bar Retrofit - Do\'s And Dont\'s 2003
Abstract:
This report documents construction and inspection guidelines for the successful construction of a dowel bar retrofit project.

Authors:
Pierce,L., Uhlmeyer,J. S., Weston,J. T.

Keywords:
construction, construction techniques, dowel alignment, dowel bar, Dowel bar retrofit, inspection, project, retrofit


Download Report:
External Links:
http://www.wsdot.wa.gov/research/reports/fullreports/576.1.pdf http://wsdot.wa.gov/Research/Reports/500/576.1.htm
Orsborn,J. F. WA-RD 545.2 Culvert Design Flows For Fish Passage And Structural Safety In Ease Cascade and Blue Mountain Streams 51 2002
Abstract:
The pervasive problem of restoring fish runs to their natal streams is characterized in many regions of Washington by improperly placed culverts. The replacement of these fish migration barriers requires knowledge of design flows: floods for structural safety and migration season high and low flows. High flows block fish passage with velocities that exceed their swimming capabilities. During low flows, the migration barrier is caused by a lack of enough water depth to support the bodies of the fish. The estimation of these fish passage and safety flows in ungaged streams is impeded in eastern Washington due to: the wide range of conditions (5 to 110 inches per year of precipitation); diverse geology and soils; a lack of stream-gaging stations with long-term records; changes in land use; and the seasonal impacts of irrigation diversions and well on the remnant flows. Past efforts to estimate these flows have not been successful. Therefore, the WSU project was undertaken to model the high migration season flow in all of eastern Washington. In addition, WSU established 20 stream-gaging stations on salmon streams along the east side of the Cascade Mountains plus the Blue Mountains. Our complementary project was developed to estimate other design flows in the Water Resource Inventory Areas and 49, in which the WSU gage sites are located. United States Geological Survey (USGS) gage records in those (and in and 47) were used to develop our models that estimate the following statistical flows: 100-year, 25-year and 2-year daily and peak floods; the average annual flow and its variability; ranges of mean monthly flows (maximum, average and low); the 7-day average, 2-year, 10-year, 20-year low flow; and the 30- and 60-day average low flows. The model results are, for the most part, very good. The standard error of estimate ranges are: for floods, 2 -37%; average annual flow, 10-37%; maximum annual flow, 6 -14%; annual flow, 13 -23%; and flows, 3 -22%. Monthly average flows reflected the strong influences of seasonal variability and irrigation withdrawals: due to winter frozen Iowa flows (3%)in the Entiat,-Wenatchee Region, and August low flows (242%) in the Blue Mountains due to irrigation. All flow estimation equations were based on USGS stream-gaging data from continuous located in the located in the WRIA'S.

Authors:
Orsborn,J. F., Orsborn,M. T.

Keywords:
Annual, barrier, barriers, condition, culvert, culverts, data, design, design flows, developed, equations, Error, fish, fish passage, flood, flow, hydrologic models, impact, impacts, ITS, land use, land-use, model, models, project, safety, salmon, season, seasonal, soil, structural safety, survey, velocity, Washington, winter


Download Report:
External Links:
http://www.wsdot.wa.gov/research/reports/fullreports/545.2.pdf http://wsdot.wa.gov/Research/Reports/500/545.2.htm
Mahoney, J.P. WA-RD 487.1 Summary Report On The State Pavement Technology Consortium 2000 TRAC/UW
Abstract:
This report documents the first year results of a pooled fund study among four states (California, Minnesota, Texas, and Washington State) and describes the structure and objectives. The planned continuation of this collaboration during the next two years is described. The pooled fund project established a working relationship among the four State DOT organizations. Under this agreement, each state allocated funding to allow selected DOT personnel and university researchers to participate in a series of technical meetings. Washington acted as the lead state for this pooled fund project, and produced the minutes and other documentation.Four technical meetings were held between July 1999 and January 2000, one in each of the four participating states. The general format for these meetings included presentations from the host DOT and associated research institutions, followed by specific topics of common interest to the four states. The four states quickly identified topics of mutual interest via this process. To provide the ability to study these topics and those identified in the future, the State DOT research managers agreed to establish a management framework to continue information sharing, to plan funding commitments and assure proper oversight and management of the collaborative studies.described.

Authors:
Mahoney, J.P., Pietz, M.D., Anderson, K.W.

Keywords:
California, Consortium, framework, management, Meeting, Minnesota, objectives, pavement, project, research, Study, technology, Texas, Washington, Washington state


Download Report:
Wetherby,B. WA-RD 462.6 SWIFT - Evaluation Summary 1999
Abstract:
The SWIFT (Seattle Wide-area for Travelers) project was a field operational test of a wide area ITS communications system using a flexible FM sub-carrier High Speed Data System (HSDS). The test was conducted in a partnership with WSDOT, King County Metro Transit, Delco Electronics, Inc., IBM, Seiko Communications Systems, Metro Traffic Control and the Federal Highway Administration. Three devices were used, by the public, to receive the traveler a Delco car radio (capable of providing vector navigation in addition to personal paging and the messages); a Seiko wrist watch pager; and a portable computer (capable of providing graphic displays of traffic advisories and bus positions). After the 15-month test, interviews with the 600 Seattle commuters/participants were conducted to assess user acceptance. A communications study evaluated the adequacy of the HSDS system to disseminate traveler information. Architecture study assessed the effectiveness of the various components to carry out SWIFT operations. institutional issues study documented the history of the project and assessed the institutional issues confronted. A deployment cost study investigated the cost of deployment of a SWIFT system and assessment of potential profitability. The first five reports in this series detail individual aspects of the project.

Authors:
Wetherby,B., Perez,W.

Keywords:
Acceptance, Assessment, bus, computer, control, cost, counties, data, Deployment, effectiveness, evaluation, highway, Institutional, interviews, Issues, ITS, Miscellaneous Library, paging, portable computer, project, public, seattle, speed, Study, SWIFT, System, systems, traffic, traffic advisories, traffic control, transit, traveler information, WSDOT


Download Report:
Muench, S. T. WA-RD 476.2 Evaluation of the Transtech Pavement Quality Indicator 1999 TRAC/UW
Abstract:
Recently, WSDOT acquired a non-nuclear, non-destructive, density measuring device manufactured by TransTech called a Pavement Quality Indicator (PQI). TransTech\\\\\\\'s PQI measures pavement density indirectly by measuring its dielectric constant. A non-nuclear gauge is advantageous because it contains no radioactive source and is therefore not subject to radiological controls, and it can obtain readings in about 5 seconds versus to 4 minutes with a nuclear gauge. Currently, TransTech is collecting data from different agencies to determine the suitability for measuring asphalt pavement density. This brief study presents density measurements from PQI and compares them with nuclear density gauge and core density measurements from three WSDOT 1998 paving projects. This evaluation was a secondary study to 1998 study Asphalt Concrete Temperature in Washington State; therefore this study\\\\\\\'s experimental design was based entirely on the Temperature study requirements, which resulted in non-random samples and multiple populations within the same sample groups. Despite these problems, results indicate that, when averaged, PQI readings compare favorably with both nuclear measurements and core measurements.

Authors:
Muench, S. T., Mahoney, J. P., Cawley, B.

Keywords:
Agencies, asphalt, asphalt concrete, asphalt pavement, concrete, control, core densities, data, density, design, evaluation, experimental, group, indicator, ITS, nuclear gauge, pavement, pavement quality, pavement quality indicator, population, project, quality, Study, temperature, Washington, Washington state, WSDOT

Wetherby,B. WA-RD 462.4 SWIFT - Institutional Issues 1998
Abstract:
The Seattle Wide-area Information for Travelers (SWIFT) project was a highly successful Intelligent Transportation System (ITS) Field Operational Test (FOT) that was conducted over a four-year period from 1993 to 1997. The purpose of the project was to test the efficacy of a High Speed Data System (HSDS), or FM Sub-carrier, to disseminate incident, bus and speed congestion information via three different end-user devices: pager watch, portable computer and in-vehicle navigation device. Six hundred ninety (690) commuters, many with route- or mode-choice options, participated in the FOT and provided user-acceptance evaluations. Other evaluation components examined the system architecture, communications coverage, deployment cost and institutional issues that affected the project.The primary purpose of the SWIFT Institutional Issues Study evaluation was to collect information regarding the institutional issues (e.g., policies, jurisdictional issues, internal and external factors) that affected design, development, testing, deployment and conduct of the SWIFT Field Operational Test (FOT); determine how these issues were overcome and what lessons could be learned. A secondary purpose of the evaluation was to document the history of the SWIFT project.The methodology for the SWIFT Institutional Issues Study consisted of two sets of questionnairesand two sets of semi-structured interviews that were conducted with fourteen (14) SWIFT team memberrepresentatives at two different points during the conduct of the SWIFT FOT: about midway through the conduct of the test and after the test was completed. All SWIFT team member responses were independently collected and SWIFT institutional issues were primarily identified by determining which topics were addressed by two or more individuals. Historical information was collected from various sources throughout the project.SWIFT represents one of the first ATIS FOTs conducted in this country. Earlier tests were conducted in Orlando, FL (TravTek) and Minneapolis St. Paul (Genesis) among others, yet the SWIFT FOT appears to have extended considerably the available database of information regarding ATIS effectiveness and acceptance. The addition of real-time bus information, in particular, has set the SWIFT FOT apart from others already conducted.One of the significant aspects of the SWIFT teaming agreement was the long-term interest in ITS and commitment of the organizations involved. For instance, the majority of the SWIFT team members articulated a long-term interest in ITS deployments. In addition, three organizations-Seiko, Etak and Metro Traffic Control-+ommitted themselves to fielding a \"SWIFT-like\" system after the project was completed. This degree of interest and commitment resulted in all of the SWIFT team members working together in a very effective, cooperative fashion throughout the FOT.A critical organizational structure that was instituted to implement SWIFT was the weeklyteleconference. This simple, yet cost-effective method of managing and discussing the technicalissues involved with the project was attributed by many of the SWIFT team members to aprimary instrument of the project\'s success. In particular, the SWIFT teleconferences enabledthe representatives of each organization to keep abreast of the developmental status of theproject, to brainstorm solutions to encountered problems and to develop scheduling sense.

Authors:
Wetherby,B.

Keywords:
ATIS, bus, computer, congestion, congestion information, cost, data, database, design, development, effectiveness, evaluation, incident, Institutional, Intelligent transportation system, interviews, Issues, ITS, methodology, mode choice, policy, portable computer, project, scheduling, seattle, speed, SWIFT, System, tests, traffic, transportation


Download Report:
Jensen,M. WA-RD 462.3 SWIFT - Deployment Cost Study 1998
Abstract:
The Seattle Wide-area Information For Travelers (SWIFT) project was a highly successful Intelligent Transportation System (ITS) Field Operational Test (FOT) that was conducted over a four-year period from 1993 to 1997. The purpose of the project was to test the efficacy of a High Speed Data System (HSDS), or FM Sub-carrier, to disseminate incident, bus and speedlcongestion information via three different end-user devices: pager watch, portable computer and in-vehicle navigation device. Six hundred ninety (690) commuters, many with route- or mode-choice options, participated in the FOT and provided user-acceptance evaluations. Other evaluation components examined the system architecture, communications coverage, institutional issues, and consumer acceptance. The primary purpose of the SWIFT Deployment Cost Study was to provide an independent Life Cycle Cost Estimate (LCCE) of an operational and fully deployed SWIFT system. Moreover, it is intended to provide both the SWIFT participants and the FHWA with a measure of the commercial viability of \"SWIFT-like\" systems nationwide. Table ES- 1 shows the organizations that were included in the SWIFT Deployment Cost Study LCCE and commercial viability analysis.Table ES-1. Deployed SWIFT Participants (CostIRevenue Participants).Industry Government/InstitutionaISeiko Communications Systems, Inc. (SCS) King CountyMetro Networks University of WashingtonEtak, Inc.IBM (FOT Development Only)Delco Electronics (FOT Development Only)The methodology for the SWlFT Deployment Cost Study LCCE relied on standard proven costestimation and data collection and analysis techniques to provide cost estimates for each SWIFTparticipant shown above across the following three life-cycle phases:1) FOT development (costs of current SWIFT Test)King County Metro TransitUniversity of Washington (UW)2) Commercial Development (additional development and procurement costs for fullydeploying an operational SWIFT system (follows the completion of the SWIFT test)3) Annual Commercial Operations (annual operations costs for a fully deployed SWIFTsystem)A summary of the resulting life cycle cost estimate (LCCE) for the deployed SWIFT system ispresented in Table ES-2. Here, the FOT Development phase (based on SWIFT test actuals) wasestimated to cost $6.4 Million, the Commercial Development phase was estimated to cost $1.5Million, and the Annual Commercial Operations costs were estimated to be $0.8 Million.-- -SWIFT Deployment Cost Study I

Authors:
Jensen,M.

Keywords:
Acceptance, analysis, Annual, bus, computer, Consumer, cost, costs, counties, data, data collection, Deployment, development, evaluation, incident, Institutional, Intelligent transportation system, Issues, ITS, methodology, Miscellaneous Library, mode choice, networks, portable computer, project, seattle, speed, Study, SWIFT, System, systems, transportation, Washington


Download Report:
Weston,R. F. WA-RD 364.2 Washington Integrated Networked Geo-Based System (Wings) Implementation Plan 1994
Abstract:
The purpose of this study is to provide the Washington State Department of Transportation, Aviation Division (WSDOT/AD) with the broad-based vision needed to apply new and emerging technology in geographic information systems (GIS) to aviation planning and reporting systems.The purpose of this study is to provide the Washington State Department of Transportation, Aviatior Division with the broad-based vision needed to apply new and emerging technology ir geographic information systems to aviation planning and systems. This is the second two reports. report documented the user needs, established data and application priorities, and presented a conceptual design for sharing geographic information pertaining to Washington\'s airports with airport sponsors, the Aviation Administration (FAA), and other WSDOT divisions. report provides an implementation plan. This report builds upon the conceptual design to provide a broad-based implementation plan. Three implementation activities are described in phases. Project organization and staffing requirements for policy, management, technical operations, and technical support are discussed in Section 3. Section 4 addresses the estimated resource requirements for WSDOT to make the implementation of WINGS a success. Included are requirements for personnel, data conversion from a manual to a computer-based system, and hardware. The of the report discusses issues and what next steps are required to begin the implementation of WINGS.

Authors:
Weston,R. F., Sandersen,J., Walker,L. A., Middleton,R.

Keywords:
airports, aviation, aviation planning, data, design, geographic information system, geographic information systems, GIS, implementation plan, information systems, management, manual, planning, policy, project, System, systems, technology, transportation, Washington, Washington state, WINGS, WSDOT


Download Report:
Pierce,L. WA-RD 346.1 Dowel Bar Retrofit, I-90 Kachess River to Yakima River 348 1994
Abstract:
This report documents the rehabilitation of a faulted Portland cement concrete pavement with epoxy coated dowel bars. The dowel bars were installed parallel with centerline at each joint to reestablish panel to panel interlock. The construction project also included the trial installation of tied PCC shoulders as a means of stabilizing the panels. Diamond grindling was also included in the contract to bring the retrofit pavement back to a smooth longitudinal profile.Early performance results indicate that the retrofit dowel bars are performing better than the tied shoulders with regard to preventing the reoccurrence of faulting.

Authors:
Pierce,L., Korynta,A.

Keywords:
concrete, construction, dowel bar, Epoxy, faulting, pavement, PCC, PCCP rehabilitation, performance, portland cement concrete, profile, project, rehabilitation, retrofit


Download Report:
Cohn,L. F. WA-RD 304.1 Special Noise Barrier Applications 1993
Abstract:
This report summarizes an investigation of the technical aesthetic, and economic feasibilities of incorporating special noise barrier applications into a highway noise control program. The intent of the report is to take as a starting point the thin, vertical, reflective barrier now used in most applications. Special barrier applications are those beyond the thin vertical reflective barrier.The investigation of technical feasibility relates to the formulation of the effects of absorptive treatments, slanted tops, T-tops, and other special applications. The economic and aesthetic feasibility investigations examine the value of employing these special applications in lieu of thin, vertical, reflective barriers. The research reported on herein was performed on behalf of the Washington State Department of Transportation. The intent of the was for background studies of the effects of special treatments, so the could be in a position to implement pilot projects at a later date.

Authors:
Cohn,L. F., Harris,R. A.

Keywords:
absorption, absorptive, applications, barrier, barriers, control, highway, Insertion Loss, noise, parallel barrier, program, project, research, transportation, Washington, Washington state


Download Report:
Kilian,A. P. WA-RD 239.1 Long-Term Performance Evaluation of Wood Fibre Fills 1992
Abstract:
This paper presents the results of a research project to determine the long-term performance of wood fibre embankments, that were constructed by the Washington State Department of Transportation (WSDOT) beginning in 1972. At the time of their construction, concern existed that wood fibre fills would only provide a 15 to 20 year service life.Performance of existing wood fibre fills was evaluated based on thequality of the wood fibre material, quality of the effluent, and condition ofthe pavement. A visual classification system rating the wood fibre from freshto completely decomposed was developed and used in order to establish acriteria from which all wood fibre mater.ia1 could be -rated.. Visual examinationin conjunction with laboratory tests were used as determining aspects for theeffluent quality. The WSDOT Pavement Management System was used to evaluate relative pavement performance. Site descriptions are presented giving specificcharacteristics and properties of the fills inventoried, An analysis of t h i sinformation was done to determine the effectiveness of the fills.Over half the wood fibre samples were found to be nearly fresh or freshand none w e found to be completely decomposed. In all but one case, thepavement quality over the wood fibre fills surpassed the comparative highwaysegment rating indicating the wood fill\'s performance exceeded thatof the surrounding area. Generally, the surface water in the vicinity of thewood fibre was found to be clean and pure indicating no adverse impact ofeffluent. Given the above findings, embankments constructed of wood fibre werefound to perform well over ahnost a 20. year period. Service life in excess of50 years can be expected - of wood fibre fills.

Authors:
Kilian,A. P., Ferry,C. D.

Keywords:
analysis, condition, construction, developed, effectiveness, Embankments, evaluation, impact, Leachate, management, management system, pavement, pavement management, pavement performance, pavements, performance, performance evaluation, project, quality, research, tests, transportation, Washington, Washington state, Wood fibre, WSDOT


Download Report:
Roper,T. H. WA-RD 243.1 Thin Overlay, South 154th Street Overcrossing 5/523E Experimental Feature 1991
Abstract:
The Washington State Department of Transportation is conducting experimental field evaluations of selected polymer concrete thin (1/4 inch) overlays. The polymer concrete material is manufactured by private industry firms and installed on selected bridge decks under standard WSDOT construction contracts. Approximately 24 bridges will be involved in the experiment; eight of these are included in federal participating construction projects as experimental features.A polymer concrete thin overlay, The Conkryl Broadcast System (methlmethacrylate), was applied to the deck of the South 154th Street Overcrossing, Bridge No. 5/523, under Contract No. 3354, SR 405 Tukwila to South Renton HOV Lanes. This bridge is a prestressed girder bridge located on the mainline I-5 at the intersection with I-405 in Seattle, Washington.

Authors:
Roper,T. H., Henley,E. H. Jr

Keywords:
bridge, bridge deck, bridge deck repairs, bridge decks, bridges, concrete, construction, contracts, Deck, evaluation, experimental, HOV, HOV lanes, lanes, overlay, overlays, polymer, polymer concrete, prestressed, project, seattle, thin overlay, transportation, Washington, Washington state, WSDOT


Download Report:
Roper,T. H. WA-RD 087.1 Cathodic Protection For Reinforced Concrete Bridge Decks - Woodinville Interchange, Post Construction Report 1986
Abstract:
Under FHWA Demonstration Project No. 34, \"Cathodic Protection for Reinforced Concrete Bridge Decks,\" a slotted cathodic protection system was installed on the ES ramp in the Woodinville Interchange during the summer of 1985. The slotted cathodic protection system involves sawing by slots longitudinally in the existing deck at one-foot centers. Platinum wire or carbon strand wire is placed in the cut slots first and then conductive polymer is filled in the slots. Electric power from a rectifier supplies current to the wire and conductive polymer. The current then flows to the top mat reinforcing steel, giving the steel protection from further corrosion. The objective of the demonstration project was to familiarize the Washington State DOT with this new technology. This objective was fulfilled. Some problem areas with the system were identified during the work:1.A more positive method of finding grounding locations from the anode to nicks, ties, etc. needs to be developed. Perhaps an instrument can be used to supplement visual inspection. 2.The necessity for having a minimum of 112-inch cover from the bottom of the slot to the top of the needs to be resolved. 3.A better method of installing the conductive polymer needs to be developed. Hand spreading of the material from plastic bags results in sloppy work. 4.Procurement time for the rectifier needs to be shortened. 5.The project, once it has started, moves along very rapidly, there is very little time for on-the-job training of workers. Workmen should have prior experience at this work. In remote areas, sources of electrical power may not be available. It will be necessary for sources of power, such as solar panels or long-lasting batteries to be developed for this system.

Authors:
Roper,T. H., Henley,E. H. Jr

Keywords:
bridge, bridge deck, bridge decks, cathodic protection, concrete, concrete bridge, construction, corrosion, Deck, developed, flow, inspection, plastic, polymer, project, protection, reinforced concrete, reinforced concrete bridge, reinforcing, reinforcing steel, steel, steel protection, supply, System, technology, training, Washington, Washington state


Download Report:
Roper,T. H. WA-RD 087.2 Cathodic Protection For Reinforced Concrete Bridge Decks - Yakima River Bridge, Post Construction Report 1986
Abstract:
Under FHWA Demonstration Project No. 34, \"Cathodic Protection for Reinforced Concrete Decks,\" a non-slotted cathodic protection system was installed on the deck of the Yakima Bridge near Yakima, Washington, in the summer of 1985. The project involved repairing deck, then fastening Raychem pre-manufactured anodes to the deck to impress current to the mat rebar. Impressing current through the concrete to the top mat steel prevents corrosion of the steel. A latex modified concrete overlay was placed over the deck anode. The objective of the demonstration project to familiarize the Washington State DOT with new technology. This objective was fulfilled. Some problem areas with the system were identified during the work: 1.A more positive method of finding electrical grounding locations from the anode to nicks, ties, etc., needs to be developed. Some ties were exposed during the scarifying operation Perhaps an instrument can be used to supplement visual inspection. 2. An effective technique of allowing concrete trucks to drive on the anode without damaging needs to be developed. 3.An effective method needs to be developed to locate breaks in the anode as well as shorts. 4. In remote areas, sources of electrical power may not be available. It will be necessary sources of power, such as solar panels or long-lasting batteries to be developed for this system. 5. Since the project, once it has started, moves along very rapidly, there is very little time on-the-job training of workers. Workmen should have prior experience at this work. These problems need to be overcome to obtain a better quality product.

Authors:
Roper,T. H., Henley,E. H. Jr

Keywords:
bridge, bridge deck, bridge decks, cathodic protection, concrete, concrete bridge, construction, corrosion, Deck, developed, inspection, latex modified concrete, overlay, project, protection, quality, reinforced concrete, reinforced concrete bridge, steel, System, technology, training, truck, trucks, Washington, Washington state


Download Report:
Peters,A. J. WA-RD 098.1 Hot Mix Recycling Evaluation In Washington State 1986
Abstract:
The Washington State Department of Transportation (WSDOT) has completed construction of twenty-four hot-mix recycle projects as of January, 1985. At the begining of this study there were sixteen completed projects that were to be examined. Evaluation of the laboratory and pavement performance data shows that WSDOT\'s initial two projects, Renslow to Ryegrass (1977) and Yakima River to West Ellensburg Interchange (1978), are still performing very we1l. Although the other fourteed projects have been constructed only within the last two and a half years, the early data indicates equally promising results. Because of the impressive pavement performance exhibited by the recycled pavements, together with hot-mix recycle benefits such as conservation of natural resources, feasibility of construction, and its cost advantage over new ACP, hot-mix recycling has become an attractive addition to the WSDOT paving program.

Authors:
Peters,A. J., Gietz,R. H., Walter,J. P.

Keywords:
asphalt, asphalt concrete, benefit, benefits, construction, cost, data, evaluation, ITS, pavement, pavement performance, pavements, performance, program, project, recycling, rejuvenating agents, Study, transportation, Washington, Washington state, WSDOT


Download Report:
Malsch,D. A. WA-RD 085.1 Evaluating The Effectiveness Of Liquid Anti-Strip Additives In Asphalt Cement 1986
Abstract:
The use of liquid anti-stripping additives (LAA) for reducing moisture damage in asphalt concrete pavements was evaluated using pavement cores from pairs of projects with-and-without LAA. Results were analyzed using the tensile strength ratio (TSR). In addition, a diazo-dye for determining the presence and concentration of LAA was attempted to access the value or the test as a field procedure. The chemical additive detection tests proved inclusive, but the TSR analysis gave a positive indication of the need for the use of LAA in the wetter environments of the state, For drier environments and for low traffic volumes, use of LAA may not be cost effective. The indirect tensile test was judged to be a potentially valuable tool for statewide use in the evaluation of stripping additive needs.

Authors:
Malsch,D. A.

Keywords:
additive, analysis, anti-stripping agents, asphalt, asphalt concrete, Asphalt Concrete pavement, bituminous concrete, Chemical, concrete, cost, cost effective, damage, detection, diazo-dye test, effectiveness, environment, evaluation, indirect tension test, moisture damage, pavement, pavement life, pavements, project, strength, stripping, tests, traffic, traffic volumes, volume


Download Report:
Nielsen,Robert S. WA-RD 043.1 Allocation Of Transportation Resources: Development Of An Evaluation Method 904 1982
Abstract:
The objective of this report is to develop an effective transportation resource allocation technique that is flexible and can be applied to various areas. Allocation procedures were developed and tested for apportioning resources to transportation services in relation to community transportation objectives. Procedures were developed and applied that measured the effectiveness of candidate transportation service proposals in terms of a transportation resource allocation index (TRAI). The extent to which a transportation proposal achieves the community objectives is defined as its effectiveness. The transportation index was computed on the basis of the projects scorings for eight selected determinants, multiplied by the weighing assigned to each determinant in accordance with their relative effectiveness.The TRAI for eight transportation service proposals including transit, were computed as a pilot study and as a working test of the techniques in the Tri-Cities area of Richland, Kennewick, and Pasco, WA. There appears to be no complication in implementing this technique for allocations in any local urban area providing the concepts are correctly evaluated and applied.

Authors:
Nielsen,Robert S., Shea,Daniel J., Yandon,Keith E.

Keywords:
Allocation of resources, developed, development, effectiveness, evaluation, index, ITS, Objective and goals, objectives, project, transit, transportation, transportation resource/allocation, transportation service, urban


Download Report:
Nelson,Thomas L. WA-RD 050.1 Development And Implementation Of Washington State's Pavement System 905 1982
Abstract:
This report describes the pavement management system developed by WSDOT staff over a period of five years. Both project-level and network-level pavement management are represented within the four broad areas of data processing which combine to constitute the foundation of the system.The design of a pavement data file is laid out together with the process of assembling it. Also shown are the methods used to analyze and convert the file data from pavement condition ratings to pavement performance curves for each project. The performance curves are then used, together with appropriate cost data, to determine the most cost-effective type and time to fix. The network-level program then summarized the need work for each year of a rehabilitation program. Mean are provided for adjusting the program to fit budget constraints or minimum acceptable levels of average pavement condition.It is concluded that the system, operating on biennial pavement condition ratings, provides a good solid framework for orderly analysis to estimate the economic benefits of the type, timing, and sequence of rehabilitation activities applied to a pavement.

Authors:
Nelson,Thomas L., LeClerc,R. V.

Keywords:
analysis, benefit, benefits, condition, cost, data, design, developed, development, foundation, framework, management, management system, methods, Operating, pavement, pavement condition, pavement data file, pavement management, pavement performance, performance, program, project, rehabilitation, System, Washington, Washington state, WSDOT


Download Report:
Nelson,Thomas L. WA-RD 050.2 Development And Implementation Of Washington State's Pavement System - Summary 906 1982
Abstract:
This report describes the pavement system developed by staff over a period of five years. Both project-level and network-level pavement are represented within the four broad areas of data processing which combine to constitute the foundation of the system. The design of a pavement data file is laid out together with the process of assembling it. Also shown are the methods used to analyze and convert the file data pavement condition ratings to pavement performance curves for each project. The performance curves are then used, together with appropriate cost data, to determine the most cost-effective type and of fix. The network-level program then the needed work for each year of a rehabilitation program. Means are provided for adjusting the program to fit budget constraints or acceptable levels of average pavement condition It is concluded that the system, operating on biennial pavement condition ratings, provides a good solid framework for orderly analysis to estimate the economic benefits of the type, timing, and sequence of rehabilitation activities apply to a pavement.

Authors:
Nelson,Thomas L., LeClerc,R. V.

Keywords:
analysis, benefit, benefits, condition, cost, cost effective, data, design, developed, development, foundation, framework, management, management system, methods, Operating, pavement, pavement condition, pavement data file, pavement management, pavement performance, performance, program, project, rehabilitation, System, Washington, Washington state, WSDOT


Download Report:
Public Transportation and Planning Division WA-RD 045.1 Impacts of Truck and Railroad Deregulation on Transportation Operation and Economic Activity in the State of Washington ... 1981
Abstract:
This is an interim report that examines the potential impacts in Washington State resulting from the adoption of the Motor Carrier Act of 1980 and the Staggers Rail Act of 1980. Adoption of the two have set aside years of rigid regulation of interstate freight movement and granted new latitudes of freedom to shippers and transportation providers. Information was obtained by surveying and interviewing shippers and freight transportation providers throughout the state. Initial indications are the impacts resulting from deregulation have been slow to emerge due to suppressed economic conditions. The study projects that as economic conditions improve and principles have time to adjust to the new laws, discernable impacts will occur.

Authors:
Public Transportation and Planning Division, Washington State Department of Transportation

Keywords:
condition, Deregulation, freight, impact, impacts, Interim, motor carrier, project, railroads, regulation, transportation, truck, trucking, Washington, Washington state


Download Report:
Mar,B. W. WA-RD 039.13 Year Four, Runoff Water Quality, August 1980-81 924 1981
Abstract:
This report focuses on the results of four research thrusts that resulted in dissertations and condensed research reports during this reporting period. There are now 14 project reports either completed or close to completion, as shown in Table 1; this report summarizes the results reported in numbers 10-12. Also summarized in Table 1 are the reports planned for the remainder of the project.

Authors:
Mar,B. W., Ferguson,J. F., Spyridakis,D. E., Welch,E., Horner,R. R.

Keywords:
project, quality, research, runoff, water quality


Download Report:
Anderson,K. W. WA-RD 046.1 Permanent Lane Markings - Recessed Edge Stripe 1981
Abstract:
The project goal was to evaluate different methods of cutting recessed skip stripe grooves, and to evaluate various pavement marking materials placed into the recesses. The project objective was to find a marking system for our mountain pass highways that would tolerate snowplowing and sanding operations, studded tires, and chain wear.Three methods of pavement grooving and three types of making material were evaluated over a four-year period. The grooving methods were evaluated with regard to production rate, the quality of the finished groove, and cost. The marking materials were checked for ease of installation, cost durability, and visibility.Only one method of grooving was found that produced the desired recess shape at a reasonable cost and in a timely manner. All three of the making materials were durable enough to survive for three years, but none produced the desired wet-daytime or wet-night visibility needed for adequate lane delineation. This loss of visibility under wet conditions was due to the lack of retroreflectance from the marking materials.

Authors:
Anderson,K. W.

Keywords:
chains, condition, cost, delineation, durability, grooves, grooving, highway, highway delineation, Highways, lane lines, materials, methods, night visibility, pavement, project, quality, rainfall, retroreflectance, snowplows, striping, studded tire, studded tires, System, tire, tires, Traffic markings


Download Report:
Whalen,K. WA-RD 040.1 Load Restriction Determination Study 930 1980
Abstract:
The project identified various highway roadways subjected to load restrictions for cataloguing on a District-wide map. An investigation of freeze-thaw events and pavement deflections was conducted in addition to collection of weather data at selected sites. "Frost Tubes" were evaluated and found to be an effectivetool for measuring frost depths. Limited data was collected due to warm winters and short freeze-thaw cycles. It was concluded that load restrictions are not needed until the temperature changes to a warming period. Additional research is needed to determine when load restrictions should be removed.

Authors:
Whalen,K.

Keywords:
data, Freeze Thaw, freeze-thaw, frost, Frost Tubes, Frozen Pavement, highway, load restrictions, pavement, pavement deflection, project, research, roadway, temperature, winter


Download Report:
Social and Econonomic Planning Section of the WA State Department of Highways WA-RD 037.1A Impact Of Highway Improvement On Property Values In Washington 933 1980
Abstract:
Transportation improvements of all kinds are being evaluated more carefully than ever during the planning stages. This attention to detail is well justified because the implications of such projects transcend the engineering disciplines and have environmental, social , and economic effects of major importance. In the economic area one of the impacts that is of great concern to the public i s the effect of a highway on property values. The purpose of this study is to measure the beneficial and adverse effects of limited- access highways on property values. A need exists in the State of Washington to have current data and analyses concerning this subject that apply specifically to this state . In addition there have been several theoretical developments that allow refinement of previous studies and validation of the results .OverviewThis study analyzed the beneficial effects of a highway on the values of surrounding properties by determining the real estate price trends in areas where a highway was constructed and comparing these trends with those in comparable areas which did not experience such changes. There were four residential areas utilized for parts of this study: Kingsgate east of Lake Washington on 1-405, north King County along 1-5 north of the Seattle city limits , Spokane near the east city limits along 1-90, and the southeast section of Puyallup along SR 512. Because of the lack of an adequate control area f o r the Spokane study, only the other three areas were used for the benefit estimation.

Authors:
Social and Econonomic Planning Section of the WA State Department of Highways

Keywords:
benefit, control, counties, data, development, environmental, highway, Highways, impact, impacts, improvement, planning, project, property values, public, seattle, transportation, Washington

Veress,S. A. WA-RD 038.1 Monitoring By Aerial And Terrestrial Photgrammetry 938 1979
Abstract:
A photogrammetric monitoring method of structural deformation has been developed during the course of this project. The method is based on a combination of aerial and terrestrial photographs.The theoretical experimentation for formulation of computer programs has beendone on mathematical model s. The combination of aerial and terrestrial photographsprovides a 30% increased accuracy if compared to terrestrial photographsonly. Practical experimentation was done on the existing Gabion Wall and itwas indicated that the achievable accuracy is 1/120,000 o f the photographicdistance. The method is flexible if it can be used for monitoring of an$type of structure as well as f o r aerialtriangulation.

Authors:
Veress,S. A., Hatzopoulos,J. N.

Keywords:
computer, computer program, developed, Gabion, model, monitoring, Photogrammetry monitoring, simultaneous adjustment, statistical analysis and space intersection, resection, program, project


Download Report:
University of Washington WA-RD 023.1A Operating Manual, Methods and Equipment Developed During The Project (Central Avalanche Hazard Forecasting), July 1975-M... 1978
Abstract:
The Central Avalanche Hazard Forecasting project has been funded by the Washington State Highway Commission since July 1975 in order to test the feasibility and effectiveness of central avalanche forecasting for the Cascade Mountain Passes and adjacent territory . Historically, avalanche forecasting in the Cascade Mountains has been done locally on an area-by-area basis by Highway Department personnel and by Forest Rangers and professional ski patrolmen at individual ski areas. This project explored the possibilities of improving both mountain weather and related avalanche forecasts for use by WSDOT during winter operations in the mountain passes and, secondarily, explored the usefulness of anarea-wide forecasting service to other, cooperating agencies. The aim of this work has been to establish the technical and administrative framework for an operational, on-going mountain weather and avalanche forecasting service for Western Washington under the joint support of interested public agencies. This aim has been achieved in autumn 1978 by the operation of an avalanche forecasting office administered by the US Forest Service, housed by the National Weather Service, and supported by WSDT, with additional peripheral support from both the public and private sectors. Previous reports published by the project include: Interim Report, June 1976 (Report No. 23.2); Final Report, June 1977 (Report No. 23.3)Implementation Report, December 1978, which will be published in Spring 1979If you would like to obtain copies of any of these reports, contact WSDOT Public Transportation and Planning Division in Olympia (SCAN 234-61 49) or the Avalanche Research Office on SCAN 323-7180 or Write Avalanche Research,Department of Atmospheric Sciences AK-40, University of Washington, Seattle,Phil Taylor, Research Engineer, has done an outstanding job of developing much of this equipment and devising methods of operation. He is, unfortunately, no longer with the University. He will be working in Autumn 1978 with the US Forest Service as a consultant in addition to his continuing work with the US Geological Survey. This Operating Manual is intended to be an informational document with limited distribution and its format reflects that informality.

Authors:
University of Washington

Keywords:
agencies, avalanche, avalanche forecasting, developed, effectiveness, equipment, forecasting, framework, hazard, highway, Interim, ITS, manual, methods, Operating, planning, project, public, research, survey, transportation, Washington, Washington state, winter


Download Report:
LaChapplle,E. R. WA-RD 023.4 Central Avalanche Hazard Forecasting - Summary Of Scientific Investigations 947 1978
Abstract:
The Central Avalanche Hazard Forecasting project had had two principal aims : The design and establishment of an avalanche data network and central avalanche and mountain weather forecasting facility to serve the highway passes and other hazard areas of the Cascade Mountains in Washington. Improvements in the practices of conventional avalanche forecasting and the introduction of new techniques in statistical analysis and pattern recognition. Achievement of the first aim has been described in previous Reports 23.2 and 23.3. This present Report 23.4 gives the results of fundamental research into avalanche forecasting theory and discusses the application of these results is to central avalanche forecasting for the Cascade Mountains of Western Washington .

Authors:
LaChapplle,E. R., Furguson,S. A., Marriott,R. T., Moore,M. B., Reanier,F. W., Sackett,E. M., Taylor,P. L.

Keywords:
analysis, avalanche, avalanche forecasting, snow, weather, data, design, facilities, forecasting, hazard, highway, project, research, Washington


Download Report:
Veress,S. A. WA-RD 031.1 Photogrammetric Monitoring Of A Gabion Wall 952 1977
Abstract:
A photogrammetric monitoring method of structural deformation has been developed during the course of this project. The Gabion Wall which is part of the I-90 project has been used as the site for practical tests of the theorectical development. The monitoring consists of photographing the structure from three camera stations with KA-2 f=24" camera. The camera has been modified to a plate camera to provide the maxium accuracy.The methodology consists of the geodetic determination of the camera location and the orientation and photogrammetric determination of targets (natural and artificial) on the structure. During the course of this project more than 100 target locations were determined by three dimensional coordinates. the maximum error was found to be + 3/4 inch; the average, 1/2 inch. This represents a relative accuracy of from 1/58,00 to 1/120,00 of the photographic distance.Using the actual construction site for research has permitted immediate implementation. The instrumentation as well as the methodology along with the computer program has been transmitted to the Washington State Highway Department and their Photogrammetric Branch has been assisted in the implementation.

Authors:
Veress,S. A., Flint,E. E., Sun,L. L., Jinina,C.

Keywords:
camera, computer, computer program, construction, developed, development, Error, Gabion, highway, methodology, monitoring, Photogrammetry, Gabion Wall, deflection, camera stations, orientation matrices, space intersection space resection, program, project, research, tests, Washington, Washington state


Download Report:
LaChapplle,E. R. WA-RD 023.3 Central Avalanche Hazard Forecasting - Final Report, Phase II 954 1977
Abstract:
This report reviews the second year of work on the Washington State Highway Commission Department of Highways project Central Avalanche Hazard Forecasting (WSDH Agreement Y-1700) to test the feasibility and effectiveness of central avalanche forecasting for the Cascade Mountain passes and adjacent area. The possibilities and techniques for improving both mountain weather and related avalanche forecasts for use by WSDH during winter operation in the mountain passes were further explored, and, secondarily, the usefulness of an area wide forecasting service to other cooperating agencies. This report defines and significant changes from the first year of operation in collection, assimilation or transmission of snow, weather and avalanche data by the Forecasting Office, and details modifications of the data network itself, especially new instrumentation and telemetry equipment . Weather and avalanche forecasting accuracy and reliability are assessed by comparing daily weather and avalanche forecasts with file d data. The conceptual framework and analytical methods used by forecasters to deduce current and probable future avalanche activity from the available data network input and current and extrapolated meteorological data are presented. A general preliminary guide to forecasting methodology for the Washington Cascades is defined and discussed.

Authors:
LaChapplle,E. R., Moore,M. B., Reanier,F. W., Sackett,E. M.

Keywords:
agencies, avalanche, avalanche forecasting, snow, weather, data, effectiveness, equipment, forecasting, framework, hazard, highway, Highways, methodology, methods, project, reliability, review, Washington, Washington state, winter


Download Report:
Social and Econonomic Planning Section of the WA State Department of Highways WA-RD 025.0 Social Factors In Transportation Planning 1976
Abstract:
This report presents a summary of the research project which resulted in the following guideline reports.25.1 Development and Implementation of Community Involvement Programs25.2 Indentification And Measurement of Social Factors in Transportation Planning25.3 Conducting Surveys Concerning Transportation25.4 Operation of Interdisciplinary Teams25.5 Team Scheduling and Management

Authors:
Social and Econonomic Planning Section of the WA State Department of Highways

Keywords:
Community Involvement, Social Factors, Socio-Economic Surveys, Inter-disciplinary Team Operation and Management, development, Executive Summary, management, planning, project, research, scheduling, survey, Surveys, transportation, transportation planning


Download Report:
LaChapplle,E. R. WA-RD 023.2 Central Avalanche Hazard Forecasting - Interim Report, Phase II 1976
Abstract:
This report summarizes the first year of activity under Washington State Department of Highways project Central Avalanche Hazard Forecasting (Agreement Y-1700) to test the feasibility and effectiveness of central avalanche forecasting for the Cascade Mountain Passes and adjacent territory . This project explores thepossibilities of improving both mountain weather and related avalanche forecasts for use by the WSDH during winter operations in the mountain passes, and, secondarily, explores the usefulness of an area-wide forecasting service to other, cooperating agencies. The eventual aim of this work is to establish thetechnical and administrative framework for an operational, on-going mountain weather and avalanche forecasting service for Western Washington under the joint support of interested public agencies.

Authors:
LaChapplle,E. R., Moore,M. B., Reanier,F. W.

Keywords:
agencies, avalanche, avalanche forecasting, snow, weather, effectiveness, forecasting, framework, hazard, highway, highways, Interim, project, public, Washington, Washington state, winter


Download Report:
Social and Econonomic Planning Section of the WA State Department of Highways WA-RD 025.4 Guidelines For The Operation Of Inter-Disciplinary Teams HR-527 1975
Abstract:
In the of Washington interdisciplinary teams have been formed for planning projects a major social, economic or environmental impact. The responsibilities of the teams are as follows: Conduct in-depth studies; and implement a community involvement program; and (3) Develop a departmental recommendation for solutions to transportation problems. The inter-disciplinary teams that have used have had a wide variety disciplines represented, purpose this document is to outline procedures and discuss methods that will assist interdisciplinary team members and project engineers in carrying out their responsibilities. Part with the organization and responsibilities of the team and of its members, Part 2 sets forth ten steps recommended for teams to follow in carrying out their charge. Part 3 discusses some of the practical operating problems, which teams have experienced, and possible solutions. Methods to achieve more effective interaction among interdisciplinary team members are discussed. Also, suggestions by which technical studies and community values and attitudes can be integrated into the team's final report are included,

Authors:
Social and Econonomic Planning Section of the WA State Department of Highways

Keywords:
attitudes, environmental, environmental impact, impact, Interdisciplinary team operations, Organization and Responsibilities, Design Team Studies, Study Plan Development and Methodology, Team Management, ITS, methods, Operating, planning, program, project, transportation, transportation planning, Washington


Download Report:
Jacobson,R. WA-RD 025.5 Guidelines For Teams Scheduling and Management 1975
Abstract:
The purpose of this document is to present an effective method by which the scheduling and coordination of the activities of interdisciplinary teams can be carried out. A number of more traditional techniques of project control have not met the unique requirements of scheduling and managing the activities of an inter-disciplinary team since the basic logic of task ordering is time sequentiality. Quite a number of the activities of inter-disciplinary team can be carried on simultaneously or at any time within the project's period. The system developed within this document uses the principal of "nested" descriptions of program activities and then proceeds to develop operational procedures. The role of the individual team members as well a the overall project development is described.

Authors:
Jacobson,R., Parker,R.

Keywords:
control, developed, development, management, program, project, scheduling


Download Report:
Klasell,J. A. WA-RD 018.1 Acoustical Barrier Noise Characteristics Research Project, HR 535 HR 475 1974
Abstract:
This study was chiefly aimed at determining if a standard precast concrete median barrier placed on a highway shoulder in a fill section, would be effective in reducing highway traffic noise outside of the roadway prism. Secondly, it attacked the question of whether the current computer noise prediction program was giving accurate values.The first phase of the study consisted of collecting noise and traffic measurements in the field, first without and then with a median barrier, at two selected test sites. Next, the geometry of the test sites and field traffic data were entered into the computer program and the predicted noise levels obtained.The second phase consisted of comparing these two sets of data to determine the accuracy of the computer program and the amount of sound reduction, if any, due to the median barrier.The results indicated that the highway traffic noise was dominated by truck generated noise. It was therefore concluded that a standard median barrier will not provide a significant amount of sound reduction, outside of the roadway prism, when placed on a highway shoulder in a fill section. The results also indicated that the current computer noise prediction program will calculate noise levels that are usually higher than actually exist.

Authors:
Klasell,J. A., Butler,B. W.

Keywords:
Acoustical barrier, barrier attenuation, computer, computer program, concrete, data, ground attenuation, highway, median, median barrier, noise, Noise Levels, precast, precast concrete, prediction, program, research, roadway, traffic, traffic data, traffic noise, truck, wind, wind noise, barrier, project

Sorensen,H. WA-RD 009.3 Studded Tire Pavement Wear Reduction And Repair Phase III 994 1973
Abstract:
This report presents results obtained from the analyses of data which were collected during the performance of Phase I and Phase of this project. The data were at the A. Riedesel Pavement Testing Facility which is operated by Washington State University and is located in Pullman, Washington. Regression analyses were formed in order to relate various factors to each other. The factors used in the analyses included stud type, stud protrusion, speed, air temperature, pavement temperature, environmental conditions, stud hardness and tread depth. The purpose was to evaluate the relative importance of these factors pavement wear. It was found that the type of overlay, the type of stud and the protrusion length were the most important factors affecting pavement wear under Test conditions. The other factors could not be sufficiently isolated to determine their relative importance. Average wear rates were calculated for the different types of pavements and by the different stud types. A formula was developed which can be used to calculate pavement life under certain conditions. The results obtained for Phase I and Phase were compared and the difference in these results is discussed. Some of the difference was due to the different between the two phases A comparison with other associated research was madeA striping paint study was made and the results are in this report.

Authors:
Sorensen,H.

Keywords:
condition, data, developed, environmental, facilities, overlay, pavement, Pavement Durability, life & performance, asphalt pavement, portland cement concretes, overlays, surface textures, studded tires, skid resistance, pavement life, pavement temperature, pavements, performance, project, regression, repair, research, speed, striping, striping paints, Studded, studded tire, Study, temperature, tire, Washington, Washington state


Download Report:
Krukar,M. WA-RD 009.1 Studded Tire Pavement Wear Reduction and Repair - The Effect Of Studded Tires On Different Pavements And Surface Texture... 1972
Abstract:
This report presents results obtained from testing at the G. A. Riedesel Pavement Testing Facility at Washington State University during the period from February 11 to May 4, 1972. The purpose of this project was fourfold: 1) to determine pavement wear caused by studded tires ; 2) to evaluate the resistance of different pavement materials and textures used in the states of Washington and Idaho to wear caused by tire studs; 3) to test pavement materials and overlays to reduce tire stud damage; and, 4) to study the effect of studded truck tires on pavements. Ring #5 consisted of three concentric tracks on which 16 tires travelled in eight wheel paths. Three studded types and unstudded passenger tires , three studded and unstudded truck tires, and 46 sections of various types of pavement materials surface overlays and surface textures were tested. The results are based on wear in terms of rate of wear, area removed, maximum and average rut depth using the WSU Profilometer, and the camera wire shadow apparatus, and are valid only under WSU testing conditions. The findings indicate that some pavement materials are more resistant to the effect of studded tires than others. All types of studded tires tested caused some pavement wear and this affected the skid resistance values. The new types of studs reduced wear of various pavement materials. Studded truck tire wear was less than expected due to equipment problems.

Authors:
Krukar,M., Cook,J. C.

Keywords:
camera, condition, damage, equipment, facilities, materials, overlay, overlays, pavement, Pavement Durability, life & performance, asphalt pavement, portland cement concretes, overlays, surface textures, studded tires, skid resistance, pavements, project, repair, resistance, skid resistance, studded tire, studded tires, studs, Study, tire, tires, truck, Washington, Washington state


Download Report:
Krukar,M. WA-RD 009.1A The Effect Of Studded Tires On Different Pavement And Surface Textures 1010 1972
Abstract:
This preliminary report presents data obtained from testing at the L A Riedesel Pavement Testing Facility during the period from February 11 t o May 4, 1972. The purpose of this project was four fold: (1) to determine pavement wear caused by studded tires; (2) to evaluate the resistance of different pavement materials and textures used in the states o f Washington and Idaho to wear caused by tire studs; (3) t o test pavement materials and overlays to reduce tire stud damage; and, (4) to study the effect of studded truck tires on pavements.This preliminary report presents data obtained from testing at the G. A. Riedesel Pavement Testing Facility, during the period from February 11 to May 4, 1972.

Authors:
Krukar,M., Cook,J. C.

Keywords:
damage, data, facilities, materials, overlay, overlays, pavement, Pavement Durability, life & performance, asphalt pavement, portland cement concretes, overlays, surface textures, studded tires, skid resistance, project, resistance, studded tire, studded tires, studs, Study, tire, tires, truck, Washington


Download Report:
Krukar,M. WA-RD 009.2 Studded Tire Effects Wear Reduction and Repair Phase II - Final Draft 1008 1972
Abstract:
This report presents results obtained from testing at the A. Riedesel Pavement Testing Facility at Washington State University during the period of November 20, 1972 to May 1973. The purpose of this project was three-fold: (1 to determine pavement wear caused by studded tires; 2) to evaluate the resistance of different pavement overlays used in the states of Washington and Idaho to wear caused by studs; and 3) to test pavement materials and overlays to reduce tire stud damage. Ring and Phase of this project consisted of three concentric tracks on which 16 tires traveled in eight wheel paths. Four types of studs in passenger snow two types of passenger tires, and unstudded truck tires, and 22 sections of various types of pavement overlays and surfacings were tested. Four different stripes were also tested. The results are based on wear in terms of rate of wear, area removed, maximum and average rut depths using the WSU profilometer and the camera wire shadow box apparatus. Skid resistance values were measured using the California Skid Tester and the English Portable Skid Tester. The results are valid only under WSU testing conditions. The findings indicate that some pavement overlays are resistant to the effect of studded tires than others. All types of studded tires tested caused some pavement wear and this affected skid resistance values. Some of the newer types of studs reduced wear of various pavement overlays. The pavements having the most wear resistance had the skid resistance retention characteristics. Additives to asphalt skid resistance helped wear resistance characteristics but lowered skid resistance on characteristics.

Authors:
Krukar,M., Cook,J. C.

Keywords:
asphalt, California, camera, condition, damage, facilities, materials, overlay, overlays, pavement, Pavement Durability, life & performance, asphalt pavement, portland cement concretes, overlays, surface textures, studded tires, skid resistance, pavements, project, repair, resistance, skid resistance, snow, studded tire, studded tires, studs, tire, tires, truck, Washington, Washington state


Download Report:
LaChapplle,E. R. WA-RD 008.1 Avalanches On The North Cascade Highway SR20 1018 1971
Abstract:
This report covers activities for the eighteen months ending September 1971 under a Washington State Highway Department Contract for Research Project No. Y1301 with the University of Washington. Snow and avalanche climate varies widely across the parts of the Cascade Mountains spanned by SR-20. Little information is presently available about temperatures and weather patterns over the passes, but a limited amount of snow depth data are available from snow courses. These snow data are presented and analyed.

Authors:
LaChapplle,E. R.

Keywords:
avalanche, Avalanches, data, highway, Highway SR 520, North Cascade, project, research, snow, temperature, Washington, Washington state


Download Report:

Previous Next


TRAC